Mitsubishi Heavy Industries DXK06ZSA-W User Manual Download

Page: 14 / 40

– 12 –

OPERATION MODE select button

Each time the button is pressed, the
mode changes.

The above illustration shows all controls, but in practice
only the relevant parts are shown.

ALLERGEN CLEAR button

This button selects ALLERGEN CLEAR
operation.

ON/OFF (luminous) button

Press to start operation, press again
to stop.

TEMPERATURE button

This button sets the room temperature.

AIR FLOW (UP/DOWN) button

This button changes the airflow (up/
down) direction.

TIME SET UP switch

This switch is used for setting the time.

SLEEP button

This button selects SLEEP operation.

MENU switch

This switch selects the SELF CLEAN
operation, display brightness adjustment
and PRESET operation.

ON TIMER button

This button selects ON TIMER operation.

TIMER button

This button is used for setting the current
time and timer function.

ACL switch

This switch resets the program to default
state.

PROGRAM button

This button sets WEEKLY TIMER.

Operation and display section for remote control

HI/ECO button

This button changes the HIGH POWER/
ECO operation.

AIR FLOW (LEFT/RIGHT) button

This button changes the airflow (left/
right) direction.

SILENT button

This button sets the SILENT operation.

OFF TIMER button

This button selects OFF TIMER
operation.

WEEKLY button

This button switches the WEEKLY
TIMER to ON/OFF.

FAN SPEED button

Each time the button is pressed, the fan
speed changes.

3D AUTO button

This button sets 3D AUTO operation.

NIGHT SETBACK button

This button sets NIGHT SETBACK
operation.

SET/Child lock button

Use this button to set the timer and
Child lock.

CANCEL button

This button cancels the ON timer, OFF
timer, and SLEEP operation.

Transmission section

Transmission procedure

When each button on the remote control is
pressed – with the remote control pointing
towards the air-conditioner unit, a signal is
transmitted.
When the air-conditioner receives the signal
correctly, it will beep.

The current time, day of the week,
and present OPERATING MODE are
displayed while the air-conditioner is
turned off.

[View with the cover opened]

Page 13,15

Page 24

Page 16

Page 25

Page 19

Page 18

Page 17

Page 20

Page 26

Page 17

Page 14

Page 16

Page 25

Page 10

Page 20

Page 9,13

Page 13

Display in OFF status

RLF012A104_EN.indd 12

1/13/2017 6:35:41 PM

Summary of Contents for DXK06ZSA-W









































Search results

Summary of Contents for DXK06ZSA-W

Reviews:

Related manuals for DXK06ZSA-W

Brands by name

Popular brands

Mitsubishi Heavy Industries DXK06ZSA-W, User Manual

Search results

Summary of Contents for DXK06ZSA-W

Reviews:

Related manuals for DXK06ZSA-W

Brands by name

Popular brands