9
J
Canceling Holiday Setting
HOW TO PERFORM THE TIMER OPERATION
< WIRED REMOTE CONTROL (RC-E series) >
J
Weekly timer Holiday Setting
It is possible to temporarily disable each day’s timer setting by using the Holiday Setting. When the Holiday
Setting is cancelled, the timer setting is enabled again.
1
In the Weekly timer mode, select and set
“
”.
☞
See “Selection of Weekly timer mode” step
1
to
5
on page 8.
“
” is displayed in the display area
(
ź
is flashing)
“
” is displayed.
2
Press
Ÿ
or
ź
button.
Move the “
ź
” mark displayed above the days of week to the
day which you want to set as Holiday.
Press
Ÿ
and
ź
to move to the right and left respectively.
If you press the
Ÿ
button, the day (“SUN” to “SAT”) indicated with
the fl ashing “
ź
” mark will change one day at a time. If you press the
Ÿ
button when the “
ź
” mark is indicating “SAT”, multiple “
ź
” marks
will appear and fl ash above “MON” to “FRI”. Press the
Ÿ
button
again, and multiple “
ź
” marks will appear and fl ash above “SUN” to
“SAT” (every day). The same schedule can be applied to all the days
indicated with the “
ź
” marks by using this function. This can be used
in case you would like to apply Holiday setting to these days.
In case press the
RESET button, the remote control will
return to the previous screen and display “
”.
3
Press
SET button.
The “
ź
” mark above the day stops fl ashing and lights, and the day set
as a holiday also lights enclosed with ( ). Then, the following is displayed.
[
] (lights)
“
” (lights for two seconds)
È
[
] (lights)
“
”(lights)
After the holiday setting has been completed, the display of the
remote control returns to that of step 1. Repeat step
2
and
3
to
continue setting further holidays.
NOTICE
If you set a day of the week for which no timer operation is set,
“
” is displayed for two seconds and the display returns
to the one shown in step
1
.
4
Press
button.
Timer mode ends.
3
2
4
1
In the Weekly timer mode, select and set
“
”.
☞
See “Selection of Weekly timer mode” step
1
to
5
on page 8.
2
Press
Ÿ
or
ź
button.
Move the “
ź
” mark displayed above the day of week to the
day on which you want to cancel Holiday setting.
Select the day of the week that has been set as holiday.
3
Press
SET button.
( ) display is turned off and the following is displayed.
[
] (lights)
“
” (lights for two seconds)
È
[
] (lights)
“
” (lights)
After the holiday setting has been completed, the display of the
remote control returns to that of step
1
. Repeat step
2
and
3
to
continue canceling further holiday settings.
4
Press
button.
Timer mode ends.
•
If you press
button while timer mode
is under setting, timer mode is canceled and the
display will return to the original one.
•
If you do not press any button for several
minutes after entering the timer mode, the
timer mode ends and the display returns to the
original one.
NOTICE
•
If you select a day of the week for which setting
have already been made, all the timer numbers
that have been set are displayed. And the details
of the timer setting for the number which has “
Ż
”
mark is displayed. You can modify the selected
setting by overwriting it.
•
If you set ON timer and OFF timer operating at
the same time, OFF timer will precede.
•
If the same two times are set for ON timer on the
same day, the lower number precedes.
J
Next setting and exiting Weekly timer mode
After “
” is displayed, “
” is displayed.
1
Press
Ÿ
or
ź
button.
By pressing
Ÿ
or
ź
button, it is possible to choose the item to set.
“
” (select the next timer operation number
within the same day)
Ľ
“
” (select the next day)
Ľ
“
” (Timer mode ends)
2
Press
SET button.
If “
” is selected, “
” is displayed.
Repeat step
3
and the subsequent steps of Weekly timer setting
on page 8.
If “
” is selected, “
” is displayed.
Repeat step
1
and the subsequent steps of Weekly timer setting
on page 8.
If “
” is selected, timer mode ends.
2
1
J
Display after Weekly timer modes setting
•
The day of the week set is underlined.
•
The
ź
mark is displayed above the current day of the week.
•
The display of all the timer operation numbers set for the
current day is turned on. The
Ż
mark indicates the next
setting number to be activated, and the set time is displayed.
•
The timer operations are executed in order, and the number
and time display are turned off when all the timer operations
for the current day are completed.
•
If you press
button while timer
mode is under setting, timer mode is canceled
and the display will return to the original one.
•
If you do not press any button for several
minutes after entering the timer mode, the
timer mode ends and the display returns to the
original one.
NOTICE
Summary of Contents for FD Series
Page 2: ......
