13
WHEN THE CHECK INDICATOR LIGHT (RED) FLASHES
INSPECTION DISPLAY, FILTER SIGN, AIR CONDITIONER NUMBER, STANDBY
,
ROOM TEMPERATURE AND BACK UP DISPLAY
< WIRED REMOTE CONTROL (RC-E series) >
J
The air conditioner stops in the event
any trouble occurs.
At the same time, the check indicator
light flashes in red and the error code is
displayed in the ON timer display area and
the following is displayed in the display area.
“
”
⇔
“
”
Ç
(Air conditioner number)
(lights for 2 seconds by turns)
Error code
Air conditioner No.
1
Press AIR CON No. button.
Enter AIR CON No. display mode.
2
Press
Ÿ
button.
AIR CON No. and error codes are
displayed in order from the lowest.
Press
ź
button to display in the reverse
order.
3
Press
button.
Return to the AIR CON of the lowest
number.
1
2
ERROR display when multiple indoor units are connected
J
If errors have occurred for all the connected air conditioning units.
Initially, the error display shows the formation of the air
conditioning unit whose number is the lowest.
Errors of other air conditioning unit can be checked with the following
procedure.
1
Press AIR CON No. button.
AIR CON No. display mode appears.
2
Press
Ÿ
button.
AIR CON No. are displayed in order
from the lowest. And error codes are
displayed on the unit in trouble.
Press
ź
button to display in the reverse
order.
3
Press
button.
Return to the AIR CON of the lowest
number.
J
If errors have occurred for some of the connected AIR CON
units.
Only the units for which errors have occurred stop operating.
The remote control shows the operating units.
NOTICE
•
If
button is pressed once while errors are displayed,
the errors display is turned off, and the stop mode returns.
If
button is pressed again, the errors are displayed.
HOW TO DISPLAY AIR CON NO.
By operating AIR CON No. button, the number of the connected AIR CON unit
and error codes of the units which have the record are displayed.
1
Press AIR CON No. button.
AIR CON No. display mode appears
and the AIR CON of the lowest number
is displayed. Other displays all turn off.
2
Press
Ÿ
button.
AIR CON No. are displayed in order
from the lowest. In addition, if any
errors have occurred to the unit in
the past, error codes can be found
here too.
Press
ź
button to display in the reverse
order.
3
Press
button.
Return to the original display.
1
2
NOTICE
•
The AIR CON No. can be displayed without relation to its modes of
operation, stop, forcible stop due to an error.
•
Buttons other than “AIR CON No.” “
Ÿ
” “
ź
” “ON/OFF” cannot be
operated.
1
2
STANDBY DISPLAY
During the fi rst operation after breaker power supply input or the
recovery from power failure, “
” can be displayed on the
remote control for max 30 minutes.
The refrigerant oil protection control is activated to protect the
compressor and this isn’t a failure. Please wait till the display turns
off.
WHEN THE FILTER CLEANING MESSAGE IS DISPLAYED
The “
” is displayed
when the cumulative operation time
reaches to the predetermined number
of hours in order to notify the time for
cleaning.
J
Clean the air fi lter.
☞
See the separate printing. (HOW
TO MAINTAIN)
“FILTER CLEANING” is displayed in the
display area. It is displayed for one second
every fi ve seconds while the unit is running.
It stays lit while the system stopped.
After cleaning
1
Press
RESET button.
The cumulative operation hours are
reset and the “FILTER CLEANING”
message turns off.
1
ROOM TEMPERATURE DISPLAY
If room temperature display setting is activated, room temperature is
displayed on the remote control display. Then air fl ow display turns off,
but air fl ow adjusting button is operative. Consult your dealer for settings.
Ç
The room temperature display
BACK UP DISPLAY
If the back up display appears on the screen,. Please contact the
dealer where the unit was purchased.
The back up display is indicated per 1 second at intervals of 5
seconds when the air conditioners is in operation.
Clean the filter frequently
☞
See the separate printing.
(HOW TO MAINTAIN)
If the filter is clogged…
•
The cooling/heating capacity will get reduced. Moreover it leads
to waste of electricity and larger operation noise.
•
It may cause failure.
•
Dew may form and drop during cooling.
Do not block the inlet and outlet grilles of the
indoor and outdoor units.
Excessive load to the unit may cause failure.
Keep moderate room temperature
Too much cooling or heating is not good for your health. It will also
waste the electricity.
Block direct sunlight and prevent draft
Block direct sunlight with blinds and curtains during cooling. Close
the windows and doors except when ventilation is necessary.
Adjust the air flow properly
Do not expose yourself directly to the air fl ow for too long time. For
small animals and plants, it is harmful as well.
If you feel cold underneath your feet during heating
If the ceiling is so high that the warm air fl ow does not circulate
underneath your feet, it is recommended to use a circulator.
Consult your dealer for more detail.
Stop the operation and turn the power supply
off if there are any possibility of lightning
strikes during a thunderstorm.
Lightning strikes may lead to the failure of air-conditioning system.
FOR COMFORTABLE USE
The filter should be cleaned when
the “Filter cleaning” message
is displayed, and at the ends of
cooling and heating seasons.
HOW TO OPERATE VENTILATION
(WHEN A VENTILATOR IS INSTALLED)
< WIRED REMOTE CONTROL (RC-E series) >
1
Press
VENTI button.
“
” is displayed, and the ventilation operation begins.
Stop
Press
VENTI button again.
1
When the ventilator is set to “NO VENTI LINK”, the ventilator can be turned on and off independently regardless
of the operation of the air conditioner.
When the ventilator is set to “VENTI LINK”, the ventilator operation will be interlocked with the air conditioner
operation.
NOTICE
•
If no ventilator is connected, no operation can be performed by
pressing the ventilation button. (“
” is displayed).
VENTILATION OPERATION NOT LINKED WITH UNIT’S
OPERATION
1
Press
button.
If a ventilator is connected, ventilation will operate automatically.
“
” is displayed.
Stop
Press
button again.
NOTICE
•
No operation can be performed by pressing the ventilation button.
(“
” is displayed).
VENTILATION OPERATION LINKED WITH UNIT’S OPERATION
AIR SELECTION button can switch the air outlets.
1.
Stop the air conditioner.
2.
Select the air flow from AIR SELECTION button on the unit display.
1
In case of selecting to upper air flow.
Press the AIR FLOW SELECTION button once.
UPPER AIR FLOW LED will light for ten seconds.
2
In case of selecting to upper and lower air flow.
When UPPER AIR FLOW LED is lit by pressing AIR FLOW SELECTION button, press AIR FLOW SELECTION
button once again.
UPPER AIR FLOW LED will turn off.
Summary of Contents for FD Series
Page 2: ......
