-
215
-
'12 • PAC-T-173
NO.1
NO.3
NO.4
NO.2
⑥
②
①
③
④
⑤
⑥
②
①
③
④
⑤
[Figure 5]
[Figure 6]
[Figure 7]
Louver motor connector
Drain pump connector
Wire intake
Clamp
Louver motor wiring
Chain
Chain
6. Please rotate a hook, put in the slot on the panel, and carry out fixing the panel
temporarily. [Figure 4]
7. Tighten the two bolts used for fixing the panel temporarily and the other two.
8. Please open the lid of a control box.
9. Like drain pump wiring, please band together by the clamp and put in louver motor wiring
into a control box. [Figure 5]
10. Please connect a louver motor connector. [Figure 5]
11. Attach two chains to the intake grille with two screws. [Figure 6]
12. Replace the corner panels. Please also close a chain with a screw together
then. [Figure 7]
13. Close the intake grill.
M
ake
sure there is no stress given on the panel when adjusting the height of the indoor
unit to avoid unexpected distortion. It may cause the distortion of panel or failing to
close the air return grille.
• Any automatic control or operation from the remote controller will be disabled on the louver whose
position is fixed in the above way.
• Do not set a louver beyond the specified range. Failure to observe this instruction may result in
dripping, dew condensation, the fouling of the ceiling and the malfunctioning of the unit.
Caution
If the upper limit position number and the lower limit position number are set to the same position, the
louver is fixed at that position auto swing does not function.
Caution
When plural remote controllers are connected, louver setting operation cannot be set by slave remote
controller.
ATTENTION
Louver motor
Connector
<Range of louver setting>
※
It can be set between 24~40mm freely.
Vertical airflow direction
Dimension L (mm)
Horizontal 23
°
40
Downwards 50
°
24
Louver motor
Louver
It is possible to change the movable range of the louver on the air outlet from the wired remote controller. Once the
top and bottom position
is set, the louver will swing within the range between the top and the bottom when swing
operation is chosen. It is also possible to apply different setting to each louver.
Note: This function is not able to be set with wireless remote controll or simple remote controll (RCH-H3).
If it is necessary to fix the louver position manually, follow the procedure mentioned below.
1. Shut off the main power switch.
2. Unplug the connector of the louver motor which you want to fix the position.
Make sure to insulate unplugged connectors electrically with a vinyl tape.
3. Adjust the louver position slowly by hand so as to be within the applicable range mentioned below table.
Stop the air conditioner and press SET button and
LOUVER button simultaneously for three seconds or more.
The following is displayed if the number of the indoor units connected to the
remote controller is one. Go to step
4
.
Press
▲
or
▼
button. (selection of indoor unit)
Press SET button. (determination of indoor unit)
The following is displayed if the number of the indoor units connected to the
remote controller are more than one
Select the indoor unit of which the louver is set.
Selected indoor unit is fixed.
⑦
How to set the airflow direction
1
2
3
L
L
Caution
Caution
Lower
position
Movable
range
Upper
position
Louver No.
Piping
side
Drain
hose side
Control box
(downwards)
(horizontal)
the position of the louver
[EXAMPLE]
Press
▲
or
▼
button. (selection of louver No.)
Select the louver No. to be set according to the right figure.
4
Press
button.
Louver adjusting mode ends and returns to the original display.
For setting the swing range of other louvers, return to 1 and proceed same procedure respoctivoly.
10
[EXAMPLE]
Press
▲
or
▼
button. (selection of upper limit position)
Select the upper limit of louver movable range.
“position 1” is the most horizontal, and “position 6” is the most downward.
“position --” is to return to the factory setting. If you need to change the setting to
the default setting, use “position --”.
6
Press
▲
or
▼
button. (Selection of lower limit position)
Select the lower limit position of louver.
“position 1” is the most horizontal, and “position 6” is the most downwards.
“position --” is to return to the factory setting. If you need to change the setting to
the default setting, use “position --”.
8
[EXAMPLE]
(displayed for two seconds)
(displayed for two seconds)
(shows current setting)
(the most downwards)
(the most horizontal)
(return to the default setting)
(the most downwards)
(the most horizontal)
(return to the default setting)
(displayed for two seconds)
Press SET button. (Determination of louver No.)
The louver No. to be set is confirmed and the display shows the
upper limit of the movable range.
5
[EXAMPLE] If No.1 louver is selected,
←
current upper limit position
Press SET button. (Fixing of the upper limit position)
The upper limit position is fixed and the setting position is displayed for two
seconds. Then proceed to lower limit position selection display.
7
[EXAMPLE]
Press SET button. (Fixing of the lower limit position)
Upper limit position and lower limit position are fixed, and the set positions are
displayed for two seconds, then setting is completed.
• After the setting is completed, the louver which was set moves from the
original position to the lower limit position, and goes back to the original
position again. (This operation is not performed if the indoor unit and/or indoor
unit fan is in operation.)
9
[EXAMPLE]
NOTICE
• In case the louver No to be set is uncertain,
set any louver temporarily.
The louver will swing once when the setting
is completed and it is possible to confirm
the louver No and the position.
After that, choose the correct louver No and
set the top and bottom position.
Slot
[Figure 4]
Air leakage
Air leakage along
the ceiling
Fouling
Dew condensation or dripping
Make sure no gap is left here.
• Improperly tightened hanging bolts can
cause the problems listed below, so make
sure that you have tightened them
securely.
• If there is a gap remaining between the
ceiling and the decorative panel even
after the hanging bolts are tightened,
adjust the installation level of the indoor
unit again.
“
”
“
”
“
”
“
”
“
”
“
”
“
”
“
”
“
”
“
”
“
”
“
”
“
”
“
”
“
”
“
”
“
”
“
”
If you press R
E
SE
T button during settings, the display will r
eturn to previous display.
If you press button during settings, the mode will be ended and return to original display, and the
settings that have not been completed will become invalid.
“
”
“
”
“
”
“
”
“
”
Summary of Contents for FDC Series
