-
231
-
(c) Changing the remote control set temperature range
1) It is possible to change the set temperature range using the remote control.
a) The upper and lower set temperature limits can be set from the remote control.
Upper limit value setting: Effective during heating. The temperature can be set within a range of 20~30ºC.
Lower limit value setting: Effective when running in modes other than the heating mode (AUTO, COOL, FAN, DRY):
The temperature can be set within a range of 18~26ºC.
b) If the upper and lower limits are set using this function, the following controls are active.
2) When
and
TEMP RANGE SET under “
FUNCTION” the function setting mode is DISP CHANGE
a) If you are setting the upper limit,
If a temperature that is greater than the upper limit during heating is set from the remote control.
The unit runs for 30 minutes at the set temperature, then it automatically transmits the upper limit temperature. The
display on the remote control also approaches that temperature.
During heating, if the upper limit value is set at a temperature below the upper limit value:
The set temperature is transmitted.
b) If the lower limit is set
If a temperature that is lower than the lower limit value is set from the remote control. When running in an operation
mode other than the heating mode: the unit runs at the set temperature for 30 minutes, then it automatically trans-
mits the lower limit temperature.
If a temperature that is higher than the lower limit value is set when running in a mode other than the heating mode:
It transmits the set temperature.
3) When
and
TEMP RANGE SET under the “
FUNCTION” the function setting mode is NO DISP CHANGE.
a) If the upper limit is set
During heating, if a temperature that is higher than the upper limit is set from the remote control:
The upper limit value is transmitted. However, the remote control display does not approach the upper limit value,
but remains on the set temperature.
During heating, if the temperature is set at a value lower than the upper limit value:
The set temperature is transmitted.
b) If the lower limit is set
When in an operating mode other than the heating mode, if a temperature that is lower than the lower limit value is
set from the remote control:
The lower limit value is transmitted. However, the remote control display does not approach the lower limit value,
but remains on the set temperature.
When in an operating mode other than the heating mode, if a temperature that is higher than the lower limit value is
set:
The set temperature is transmitted.
4) Setting the upper and lower limit values
a) Stop the air conditioner, then press the SET and MODE buttons simultaneously for 3 seconds or longer. If you press “
SELECT ITEM”
“
SET”
“FUNCTION SET
” the display changes.
b) Press
the button, then change the “TEMP RANGE
” display.
c) Press the SET button and enter the temperature range setting mode.
d) Using
the
buttons, select the “Hi LIMIT SET
” or “Lo LIMIT SET ,” then fi x it by pressing SET.
e) If you selected “Hi LIMIT SET,” (enabled during heating)
“
SET UP”
“Hi LIMIT 28°C
” (blinking) is displayed.
Using the “
” temperature setting buttons, select the upper limit value. Display Example: “Hi LIMIT 26ºC
“ (blinking)
Press the SET button to fi x the setting. Display example: “Hi LIMIT 26°C” (lights up for 2 seconds)
After the fi xed upper limit value lights up for 2 seconds, the display returns to the “Hi LIMIT SET
” display in
item d).
f) If “Lo LIMIT SET
” was selected (enabled during COOL, DRY and FAN)
“
SET UP”
“Lo LIMIT 20°C
” (blinking) is displayed.
Using the
temperature setting buttons, select the lower limit. Display example: “Lo LIMIT 24ºC
” (blinking)
Press the SET button to fi x the setting. Display example: “Lo LIMIT 24°C” (lights up for 2 seconds)
After the fi xed lower limit value lights up for 2 seconds, the display returns to the “Lo LIMIT SET
” display in
item d).
g) Pressing the ON/OFF button stops the operation.
(Operation stops even if the ON/OFF button is pressed during setting, and the stopped state returns. However, if setting is
not completed, it is not valid, so use caution.)
If the RESET button is pressed during setting, the previous setting screen is displayed.
Summary of Contents for FDCVA1002HESAR
Page 107: ... 106 60 17 150 b Wireless remote controller Unit mm ...
Page 119: ... 118 Model FDCVA1002HESAR Polar white ...
Page 133: ......
