8
HOW TO OPERATE IN SILENT MODE
< WIRED REMOTE CONTROL >
1
In the timer mode, set the current day of the week
and current time.
☞
See page 4 step
1
to
7
2
Press
SET button for three seconds or more.
The remote control goes into silent mode setting and the following
is displayed.
“
” or “
” (lit)
3
Press
▲
or
▼
button.
If
▼
button is pressed, “
” is displayed.
If
▲
button is pressed, “
” is displayed.
Select “
”.
If you press the
RESET button, the remote control return to
the original screen.
4
Press
SET button.
The following setting is displayed.
“
” (flashing)
“
” (lit)
5
Press
▲
or
▼
button.
Set the “ON TIME”.
Set “Hour”
If you press
▲
or
▼
button for a while, “Hour” display is changed
by one hour, and stops when you stop pressing.
Set “Minute”
If you press
▲
or
▼
button, the display increases or decreases
by ten minutes.
If you press the
RESET button, the remote control return to
the “
” display.
6
Press
SET button.
The ON TIME is set and the following is displayed.
“
” (flashing)
“
” (lit for two seconds)
È
“
” (flashing)
“
” (lit)
7
Press
▲
or
▼
button to set the duration.
Select OFF time.
When you press
▲
button, and the duration is increased by two
hours as below, “
”
Æ
“
”
Æ
“
”
Æ
“
”
When you press
▼
button, and the duration is decreased by two
hours.
If you press
RESET buttons, the remote control return to
the “ON TIME SET”.
8
Press
SET button.
The setting is fixed and displayed.
“
” is displayed, and the silent mode setting ends.
The setting display turns off, and returns to original display.
•
•
3
•
5
•
7
2
•
4
•
6
•
8
1
When the silent mode is set, the unit operates more silently reducing noise from the outdoor unit.
The system applies the silent operation mode at the starting time to be set, and finish it after certain period has
passed.
Once the system is set to operate with the silent mode, the setting is applied everyday until it is canceled.
NOTICE
•
The remote control has main-sub units, silent setting
cannot be operated with sub unit .
•
After the silent mode is set, the following is displayed
for 3 seconds at the set time and the unit returns to
the original display.
At the ON time : “
”
At the OFF time : “
”
•
If you select “
”, you can continue the
silent mode until it is canceled. At the first ON time,
the display shows “
” for three seconds
and returns to original display.
J
Canceling Silent Mode (Setting)
Select “
” in step
2
, press
SET button and silent setting is canceled
ending the silent mode.
“
” is displayed.
SILENT MODE
J
Silent Mode Setting
• If you press
button while silent
mode is operative, silent mode is canceled
and the display will return to the original
display. Note that the setting which has not
been completed is canceled.
HOW TO PERFORM THE TIMER OPERATION
< WIRED REMOTE CONTROL >
TIMER CACELLATION MODE
2•4
7
1
3•5•6
In case “
” , “
” or “
” was
selected.
5
Press
SET button.
The detailed setting of selected timer mode are displayed
as shown below.
(But if not set, “
” is displayed)
<Display EXAMPLE when “
” is selected>
If you would like to quit cancellation, press the
RESET
button to return to the “
” display. (step 4 above)
6
Press
SET button.
The display of the detailed timer setting is turned off, and
after the message “
” is displayed for two seconds,
“
” is displayed again. (step 4 above)
Repeat steps
4
to
6
to continue canceling timer mode settings.
In case “
” was selected.
All the Weekly timer setting will be canceled if you proceed the
following steps.
To cancel a part of the timer setting, please see “Canceling
Weekly timer Mode Setting” on page 7.
5
Press
SET button.
The settings are displayed as shown below.
(But if not set, “
” is displayed)
If you would like to quit cancellation, press the
RESET
button to return to the “
” display. (step 4 above)
6
Press
SET button to confimn.
The day of the week display area turns off, and after the
message “
” is displayed for two seconds, and the
display returns to “
”. (step 4 above)
By this operation settings, for all days of the week are canceled.
1
Press
TIMER button.
Timer mode begins.
The current “The day of the week” and “the current time” are
displayed.
[
]
“
”
“
”
2
Press
▼
button for five times.
“
”
È
“
” (
▼
first press)
È
“
” (
▼
second press)
È
“
” (
▼
third press)
È
“
” (
▼
fourth press)
È
“
” (
▼
fourth press)
3
Press
SET button.
Timer Cancellation Mode begins.
4
Press
▲
or
▼
button.
By pressing
▲
or
▼
button, it is possible to choose the item to cancel.
“
”
↕
“
”
↕
“
”
↕
“
” (canceling all days of the week)
If you press the
RESET button, the remote control will
return to the previous screen, and display “
”.
(step
2
above)
7
Press ON/OFF button.
Timer mode ends.
• If you press
button while timer mode is
operative, timer mode is canceled and the display
will return to the original display.
•
If you do not press any button for several minutes
after entering the timer mode, the timer mode ends
and returns to the original display.
NOTICE
