background image

2

 DANGER

Strict compliance of the 

domestic laws must be 

observed when disposing 

the appliance.
Do not use means to 

accelerate the defrosting 

process or to clean, other 

than those recommended by 

the manufacturer.
The appliance shall be 

stored in a room without 

continuously operating 

ignition sources (for 

example: open flames, an 

operating gas appliance or 

an operating electric heater).
Do not pierce or burn.
Be aware that refrigerants 

may not contain an odour.
The appliance shall 

be stored in a well-

ventilated area where the 

room size corresponds to 

the room area as specified 

for operation.
The staff in servicing 

operations must hold 

the national qualification or 

other relevant qualifications.
This unit should be 

installed in rooms which 

exceed the floor space 

specified in installation 

sheets of indoor/outdoor 

unit.
Refer to the installation 

sheet.

Do not mount where 

flammable gas leakage 

can happen.

If leaked gas stagnates in the 

unit, the gas may cause fire.

Make sure to layout the 

drain pipe so that the 

water is completely drained.

Otherwise, water may leak and 

wet household goods.

Do not shut off the power 

supply immediately after 

stopping the operation.

Wait at least 5 minutes, 

otherwise there is a risk of 

water leakage or breakdown.

 OPERATION PRECAUTIONS

 DANGER

This appliance is not 

intended for use by 

persons (including children) 

with reduced physical, 

sensory or mental capabilities, 

or lack of experience and 

knowledge, unless they 

have been given supervision 

or instruction concerning 

use of the appliance by a 

person responsible for their 

safety. Children should be 

supervised to ensure that they 

do not play with the appliance.
Cleaning and user 

maintenance shall not 

be made by children without 

supervision.

 INSTALLATION PRECAUTIONS

 DANGER

Make sure to have the 

installation done by your 

dealer or a specialist.

If you install by yourself 

and the unit is not properly 

installed, water leakage, 

electric shock, fire and injuries 

caused by the drop of the unit 

may occur.

The preventive measures 

that the density of leaked 

refrigerant does not exceed 

the limit is necessary in case 

of installing the unit in a 

small room.

The leakage of refrigerant 

may cause oxygen deficiency 

accident. Consult your dealer 

for the measures.

 CAUTION

Make sure to perform 

grounding work.

Do not connect grounding wire 

to any gas pipe, water pipe, 

conductor rods or telephones. 

Incomplete grounding may 

cause electric shock through 

leakage of electricity.

Make sure to mount a 

leakage breaker.

Otherwise electric shock may 

occur. Please consult your 

dealer or a specialist for the 

mounting.

Do not make the room too 

cold.

It may be cause of 

deconditioning or health 

disorder.

Do not insert fingers or 

sticks into the air outlet.

It may cause injuries because 

of the fan rotating at high 

speed.

If the unit has been 

submerged under water 

due to a natural disaster 

such as flood or typhoon, 

consult your dealer before 

using it again.

If you use it as it stands, it may 

lead to failure, electric shock or 

fire.

If any abnormal symptom 

(scorched flavor etc.) is 

found, cut off the power and 

stop the operation.
Then consult your dealer. 

If you use it as it stands, it may 

lead to failure, electric shock or 

fire.

One of the causes of 

poor cooling or poor 

heating may be refrigerant 

leakage. Please consult your 

dealer.

If the repair requires additional 

refrigerant, determine the 

service with the service staff. 

The refrigerant of hydro 

module unit is not toxic.

MCD012A001_01_EN.indd   2

MCD012A001_01_EN.indd   2

2022/8/3   16:46:04

2022/8/3   16:46:04

Summary of Contents for HMU140KXZE1





















Reviews: