background image

12

When multiple IUs are connected to the remote control for a mixed environment consisting of FDKs with a left/right flap and IUs without a 

left/right flap, enabling the 3D auto flow operation will set the models without a left/right flap to a flap position set before the 3D auto flow 

operation was started.

Since the flap is controlled automatically in the following operation, it may differ from the display on the R/C.

 

 When the room temperature is higher than the set temp (In case of the heating operation)

 

  When the “In operation for heating standby. ” or “In operation for defrosting.” is displayed (In case of the heating operation).

 

  Cool air is blown horizontally not to blow directly to human body.

 

  In a high humidity environment (during cooling operation)

When you select Auto swing while the Anti draft setting (

page 32) is enabled, the flap will not swing and be set at flap position 

1 .

Changing the left/right flap direction and 3D auto flow operation cannot be performed from the SC-SL2, SC-SL3, or SC-SL4. Also note that 

3D auto flow operation will not be disabled when you change the flap direction from the SC-SL2, SC-SL3, or SC-SL4 during a 3D auto 

flow operation.

Note

   Do not manually move the flaps or panel with anti draft by force. It could damage these flaps and panels.

 

  Do not blow air downward for a long period of time during the cooling operation. Condensation may be generated and water may drip from 
the side panel. (In case of Ceiling suspended type) 

 

  For FDKs with a left/right flap, it is recommended that the flap should be set toward the right side when there is a wall on the left, or set 
toward the left side when there is a wall on the right. For more information, refer to the Notes in the Individual flap control section (

page 

31).

PJZ012A176_EN.indd   12

2018/07/04   16:42:18

Summary of Contents for RC-EX3A














































































Reviews: