Mitsubishi Heavy Industries SRK25ZJP-S User Manual Download

Page: 21 / 59

'10 • SRK-T-100

7. CAPACITY TABLES

Heat Mode

Model SRK25ZJP-S

Cool Mode

Air flow

Outdoor

air temp.

Indoor air temp

21˚CDB

23˚CDB

26˚CDB

27˚CDB

28˚CDB

31˚CDB

33˚CDB

14˚CWB

16˚CWB

18˚CWB

19˚CWB

20˚CWB

22˚CWB

24˚CWB

SHC

8.0

/min)

2.82 2.22 2.95 2.19 3.06 2.27 3.11 2.24 3.16 2.21 3.26 2.28 3.34 2.21

2.77 2.20 2.90 2.16 3.01 2.25 3.07 2.22 3.12 2.19 3.22 2.26 3.31 2.20

2.71 2.17 2.85 2.14 2.97 2.23 3.03 2.20 3.08 2.18 3.18 2.25 3.28 2.19

2.66 2.14 2.80 2.11 2.92 2.21 2.98 2.19 3.04 2.16 3.15 2.24 3.24 2.18

2.60 2.12 2.74 2.09 2.88 2.18 2.94 2.16 2.99 2.13 3.11 2.22 3.20 2.16

2.55 2.09 2.68 2.06 2.83 2.16 2.89 2.14 2.95 2.12 3.07 2.21 3.17 2.15

2.49 2.06 2.63 2.04 2.78 2.14 2.84 2.12 2.90 2.10 3.02 2.19 3.13 2.14

2.43 2.03 2.57 2.01 2.72 2.12 2.80 2.11 2.85 2.08 2.98 2.18 3.08 2.12

2.37 2.00 2.51 1.98 2.67 2.10 2.74 2.09 2.80 2.07 2.93 2.16 3.04 2.11

2.31 1.97 2.44 1.95 2.61 2.08 2.69 2.06 2.75 2.04 2.89 2.14 3.00 2.09

2.24 1.93 2.38 1.91 2.56 2.05 2.64 2.04 2.70 2.02 2.84 2.12 2.95 2.08

2.18 1.90 2.31 1.89 2.50 2.03 2.58 2.02 2.64 2.00 2.79 2.11 2.90 2.06

2.11 1.88 2.25 1.86 2.44 2.00 2.53 2.00 2.59 1.98 2.74 2.09 2.85 2.04

2.08 1.86 2.21 1.85 2.41 1.99 2.50 1.99 2.56 1.97 2.71 2.08 2.83 2.04

2.04 1.84 2.18 1.83 2.38 1.98 2.47 1.98 2.53 1.96 2.69 2.07 2.80 2.03

1.97 1.81 2.11 1.80 2.32 1.95 2.41 1.95 2.47 1.94 2.63 2.05 2.75 2.00

1.94 1.80 2.07 1.79 2.28 1.94 2.38 1.94 2.44 1.92 2.61 2.03 2.72 1.99

Air flow

outdoor

air temp.

indoor air temp

16˚CDB

18˚CDB

20˚CDB

22˚CDB

24˚CDB

9.3

/min)

-15˚CWB

1.97

1.93

1.88

1.84

1.80

-10˚CWB

2.23

2.19

2.16

2.10

2.06

-5˚CWB

2.41

2.38

2.33

2.30

2.27

0˚CWB

2.53

2.49

2.45

2.42

2.38

5˚CWB

3.22

3.19

3.17

3.10

3.06

6˚CWB

3.27

3.24

3.20

3.16

3.12

10˚CWB

3.48

3.45

3.42

3.38

3.34

15˚CWB

3.79

3.75

3.73

3.69

3.65

20˚CWB

4.07

4.04

4.02

3.97

3.94

Model SRK35ZJP-S

Cool Mode

Air flow

outdoor

air temp.

indoor air temp

16˚CDB

18˚CDB

20˚CDB

22˚CDB

24˚CDB

13.8

/min)

-15˚CWB

3.57

3.49

3.41

3.34

3.26

-10˚CWB

4.04

3.97

3.91

3.81

3.73

-5˚CWB

4.37

4.31

4.22

4.18

4.11

0˚CWB

4.59

4.52

4.44

4.39

4.32

5˚CWB

5.84

5.77

5.74

5.63

5.55

6˚CWB

5.94

5.87

5.80

5.73

5.66

10˚CWB

6.31

6.25

6.21

6.12

6.06

15˚CWB

6.86

6.80

6.76

6.68

6.62

20˚CWB

7.38

7.32

7.28

7.20

7.14

Heat Mode

Model SRK50ZJP-S

Cool Mode

Air flow

Outdoor

air temp.

Indoor air temp

21˚CDB

23˚CDB

26˚CDB

27˚CDB

28˚CDB

31˚CDB

33˚CDB

14˚CWB

16˚CWB

18˚CWB

19˚CWB

20˚CWB

22˚CWB

24˚CWB

SHC

11.0

/min)

5.63 4.02 5.90 3.95 6.11 4.02 6.22 3.97 6.32 3.90 6.51 3.95 6.69 3.80

5.53 3.96 5.80 3.90 6.03 3.98 6.14 3.92 6.25 3.87 6.44 3.92 6.62 3.77

5.43 3.90 5.70 3.84 5.94 3.93 6.05 3.87 6.16 3.82 6.37 3.88 6.55 3.73

5.32 3.84 5.59 3.78 5.85 3.88 5.96 3.84 6.08 3.79 6.29 3.85 6.48 3.71

5.21 3.77 5.48 3.72 5.75 3.84 5.88 3.80 5.99 3.74 6.21 3.80 6.41 3.69

5.10 3.71 5.37 3.66 5.65 3.79 5.78 3.75 5.90 3.70 6.13 3.78 6.33 3.66

4.98 3.64 5.25 3.60 5.55 3.74 5.69 3.71 5.80 3.66 6.05 3.74 6.25 3.63

4.86 3.57 5.14 3.53 5.45 3.69 5.59 3.66 5.71 3.61 5.96 3.70 6.17 3.59

4.74 3.51 5.01 3.47 5.34 3.63 5.49 3.61 5.61 3.56 5.87 3.67 6.08 3.56

4.61 3.44 4.89 3.41 5.23 3.58 5.39 3.55 5.50 3.52 5.78 3.63 5.99 3.53

4.49 3.37 4.76 3.34 5.11 3.52 5.28 3.51 5.40 3.47 5.68 3.59 5.90 3.49

4.35 3.30 4.63 3.27 5.00 3.47 5.17 3.46 5.29 3.42 5.58 3.55 5.81 3.44

4.22 3.23 4.49 3.21 4.88 3.41 5.06 3.41 5.18 3.37 5.48 3.50 5.71 3.41

4.15 3.19 4.42 3.17 4.82 3.38 5.00 3.38 5.12 3.35 5.43 3.48 5.66 3.40

4.08 3.15 4.35 3.14 4.76 3.35 4.94 3.36 5.06 3.32 5.37 3.46 5.61 3.38

3.94 3.08 4.21 3.07 4.63 3.29 4.82 3.30 4.94 3.27 5.27 3.42 5.50 3.34

3.87 3.04 4.14 3.03 4.57 3.26 4.76 3.28 4.88 3.25 5.21 3.40 5.45 3.32

Air flow

outdoor

air temp.

indoor air temp

16˚CDB

18˚CDB

20˚CDB

22˚CDB

24˚CDB

11.0

/min)

-15˚CWB

2.46

2.41

2.35

2.30

2.25

-10˚CWB

2.79

2.74

2.70

2.63

2.58

-5˚CWB

3.02

2.97

2.91

2.88

2.83

0˚CWB

3.16

3.12

3.06

3.02

2.98

5˚CWB

4.03

3.98

3.96

3.88

3.83

6˚CWB

4.09

4.04

4.00

3.95

3.90

10˚CWB

4.35

4.31

4.28

4.22

4.18

15˚CWB

4.73

4.69

4.66

4.61

4.56

20˚CWB

5.09

5.05

5.02

4.96

4.92

Heat Mode

Air flow

Outdoor

air temp.

Indoor air temp

21˚CDB

23˚CDB

26˚CDB

27˚CDB

28˚CDB

31˚CDB

33˚CDB

14˚CWB

16˚CWB

18˚CWB

19˚CWB

20˚CWB

22˚CWB

24˚CWB

SHC

8.5

/min)

3.94 2.87 4.13 2.82 4.28 2.89 4.35 2.85 4.43 2.80 4.56 2.84 4.68 2.75

3.87 2.83 4.06 2.79 4.22 2.86 4.29 2.82 4.37 2.78 4.51 2.83 4.63 2.73

3.80 2.79 3.99 2.75 4.16 2.83 4.24 2.79 4.31 2.75 4.46 2.81 4.59 2.71

3.72 2.75 3.91 2.71 4.09 2.80 4.18 2.76 4.25 2.73 4.40 2.78 4.54 2.70

3.65 2.71 3.84 2.67 4.03 2.76 4.11 2.73 4.19 2.70 4.35 2.76 4.49 2.68

3.57 2.66 3.76 2.63 3.96 2.73 4.05 2.70 4.13 2.66 4.29 2.74 4.43 2.66

3.49 2.62 3.68 2.59 3.89 2.69 3.98 2.67 4.06 2.64 4.23 2.72 4.38 2.63

3.40 2.57 3.59 2.54 3.81 2.66 3.91 2.64 3.99 2.61 4.17 2.69 4.32 2.62

3.32 2.52 3.51 2.50 3.74 2.63 3.84 2.61 3.92 2.58 4.11 2.67 4.26 2.59

3.23 2.48 3.42 2.46 3.66 2.59 3.77 2.58 3.85 2.55 4.04 2.64 4.20 2.56

3.14 2.43 3.33 2.41 3.58 2.55 3.70 2.55 3.78 2.51 3.98 2.60 4.13 2.54

3.05 2.39 3.24 2.37 3.50 2.52 3.62 2.51 3.70 2.48 3.91 2.58 4.06 2.52

2.95 2.34 3.14 2.33 3.41 2.48 3.54 2.47 3.62 2.45 3.84 2.56 4.00 2.50

2.91 2.31 3.10 2.30 3.37 2.46 3.50 2.46 3.58 2.44 3.80 2.54 3.96 2.48

2.86 2.29 3.05 2.28 3.33 2.44 3.46 2.44 3.54 2.42 3.76 2.53 3.92 2.47

2.76 2.24 2.95 2.23 3.24 2.40 3.38 2.40 3.46 2.37 3.69 2.50 3.85 2.45

2.71 2.21 2.90 2.21 3.20 2.38 3.33 2.38 3.42 2.36 3.65 2.49 3.81 2.43

ISC09165

Summary of Contents for SRK25ZJP-S




























































Search results

Summary of Contents for SRK25ZJP-S

Reviews:

Related manuals for SRK25ZJP-S

Brands by name

Popular brands

Mitsubishi Heavy Industries SRK25ZJP-S, User Manual

Search results

Summary of Contents for SRK25ZJP-S

Reviews:

Related manuals for SRK25ZJP-S

Brands by name

Popular brands