-
87
-
'17 • SCM-T-225
CAUTION
•
Take care when carrying the unit by hand.
If
the
unit
weight
is
more
than
20kg,
it
must
be
carried
by
two
or
more
persons.
Do not carry the unit by the plastic straps.
Always use the carry handle.
•
Do not install the outdoor unit in a location where insects and small animals can inhabit.
Insects
and
small
animals
can
enter
the
electrical
parts
and
cause
damage
resulting
in
fire
or
per-
sonal
injury
. Instruct
the
user
to
keep
the
surroundings
clean.
•
If the outdoor unit is installed at height, make sure that there is enough space for installation, maintenance and service.
Insufficient
space
can
result
in
personal
injury
due
to
falling
from
the
height.
•
Do not install the unit near the location where neighbours are bothered by noise or air generating from the unit.
It can af
fect surrounding environment and cause a claim.
•
Do not install in the locations where unit is directly exposed to corrosive gases (like sulphide gas, chloride gas), sea breeze or salty atmosphere.
It can cause corrosion of heat exchanger and damage to plastic parts.
•
Do not install the unit close to the equipments that generate electromagnetic waves and/or high-harmonic waves.
Equipment such as inverters, standby generators, medical high frequency equipments and telecom
-
munication equipments can af
fect the system, and cause malfunctions and breakdowns.
The system can also af
fect medical equipment and telecommunication equipment, and obstruct its
function
or
cause
jamming.
•
Do not install the unit in the locations where:
• There are heat sources nearby
.
• Unit is directly exposed to rain or sunlight. • There is any obstacle which can prevent smooth air circulation from inlet and outlet side of the unit. • Unit is directly exposed to oil mist and steam such as kitchen.
• Chemical
substances
like
ammonia
(organic
fertilizer),
calcium
chloride
(snow
melting
agent)
and
acid (sulfurous acid etc.), which can harm the unit, will generate or accumulate. • Drain water can not be discharged properly
.
• TV set or radio receiver is placed within 1m. • Height above sea level is more than 1000m.
It can
cause
performance
degradation,
corrosion
and
damage
of
components,
unit
malfunction
and
fire.
•
Dispose of all packing materials properly
.
Packing
materials
contain
nails
and
wood
which
can
cause
personal
injury
.
Keep the polybag away from children to avoid the risk of suf
focation.
•
Do not put anything on the outdoor unit.
Object
may
fall
causing
property
damage
or
personal
injury
.
•
Do
not
touch
the
aluminum
fin
of
the
outdoor
unit.
Aluminium
fin
temperature
is
high
during
heating
operation.
Touching
fin
can
cause
burn.
•
Do not touch any refrigerant pipe with your hands when the system is in operation.
During operation the refrigerant pipes
become extremely hot or extremely cold depending on the op
-
erating
condition.
Touching
pipes
can
cause
personal
injury
like
burn
(hot/cold).
•
Install isolator or disconnect switch on the power source wiring in accor
-
dance with the local codes and regulations.
The
isolator
should
be
locked
in
OFF
state
in
accordance
with
EN60204-1.
1. ACCESSORIES AND
TOOLS
Standard accessories (supplied with indoor unit)
(1)
Installation board
1pc
(6)
Batteries [R03 (AAA, Micro) 1.5V]
2pcs
(2)
Wireless remote control
1pc
(7)
Air-cleaning
filters
2pcs
(3)
Remote control holder
1pc
(8)
Filter holders
2pcs
(4)
Tapping screws
(for installation board ø4 X 25mm)
5pcs
(9)
Insulation (#486 50 X 100 t3)
1pc
(5)
W
ood screws
(for remote control holder ø3.5 X 16mm)
2pcs
Locally procured parts
(a)
Sleeve (1pc)
(b)
Sealing plate (1pc)
(c)
Inclination plate (1pc)
(d)
Putty
(e)
Connecting wire
(f)
Drain hose (extension hose)
(g)
Piping cover
(for insulation of connection piping)
(h)
Clamp
and
screw
(for
finishing
work)
(i)
Plastic tape
Tools for installation work
Plus headed driver
Hole core drill (65mm in diameter)
Knife
W
rench key (Hexagon) [4mm]
Saw
Flaring tool set*
Tape measure
Gas leak detector*
Torque wrench
(14.0-62.0N·m (1.4-6.2kgf·m))
Pipe bender
Plier
Gauge for projection adjustment
(Used
when
flare
is
made
by
using
conventional
flare
tool)
Pipe cutter
*
Designed
specifically
for
R410A
