-
144
-
'13 • PAC-DB-194
Pressing ACL and AIR FLOW button at the same time or
inserting the batteries with pressing AIR FLOW button will
customize the signal.
Wood screw
Holder for remote control
Installation tips for the remote control holder
Adjust and keep the holder upright
Tighten the screw to the end to avoid scratching the remote control.
DO NOT attach the holder on plaster wall.
Instruct the customer how to operate it correctly referring to the instruction manual.
Accessories
Please make sure that you have all of the following accessories.
Receiver
Wireless
remote
control
Parts set
Remote control
holder
Wood screw for holder
AAA dry cell battery
(RO3)
<To change the settings>
②
Remove the cover by unscrewing two screws from the back of receiver.
③
Change the setting by the switch on PCB.
Screws
Receiver
Backside
Backside
Default settings
Cover
Switch
④
When SW1 is turned to OFF position, change the corresponding remote control setting as
follows:
How to change the remote control setting
Note
※
When the batteries are removed, the setting will return
to the default setting.
Please make sure to reset it when the batteries are
replaced.
Caution
Instruct the customer to set the mentioned above when
replacing the batteries.
(How to set is also mentioned in the user’s manual
attached on the air conditioner.)
Installation of the receiver
①
Loosen the bolts which fix the panel and make a gap between the panel and the indoor unit
②
Put the wiring of the receiver through the opening.
③
Put the wiring on the notch on the control box so as not to be pinched by the control box and lid as
shown below.
④
Connect the wiring to the terminal block provided in the control box. (Non- polarized)
⑤
Attach the receiver to the panel according to the panel installation manual.
⑥
Fix the wiring with the clamp so that the wiring do not contact the edge of control box’s metal sheet.
⑦
Reattach the control box lid with 3 screws removed.
※
Note: Make sure the wires not to be pinched by any other parts like panel, control box and indoor unit.
Terminal block in the indoor
unit control box
Installation of the control holder
WIRELESS KIT INSTALLATION MANUAL
How to insert batteries
①
Detach the back lid.
②
Insert the batteries. (two AAA batteries)
③
Reattach the back lid.
Control plural indoor units with one remote control
Up to 16 indoor units can be connected.
①
Connect the XY terminal with 2-core wire. As for the size, refer to the following note.
②
For Packaged air conditioner series, set the indoor unit address with SW2 on the indoor
unit PCB from [0] to [F] so as not to duplicate.
Restrictions on the thickness and length of wire
(Maximun total extension 600m.)
Within 100m x 0.3 mm
2
Within 200m x 0.5 mm
2
Within 300m x 0.75mm
2
Within 400m x 1.25mm
2
Within 600m x 2.0 mm
2
Standard
Master/Slave setting when using plural remote controls
Terminal block
Remote control
③
For VRF series, set the indoor unit address with SW1, SW2 and SW5-2 on the indoor
unit PCB from [000] to [127] so as not to duplicate.
Up to two receivers can be installed in one indoor unit group.
When two receivers are used, it is necessary for a receiver to turn OFF SW2 on the receiver PCB
to set it as slave.
Attention
Caution
How to disable the Auto mode operation
VRF system (except heat recovery 3-pipe systems) cannot be operated
in Auto mode.
Make sure to set the remote control for the models so as not to be able
to choose Auto mode.
Pushing ACL and MODE button at the same time or inserting the
batteries with pressing MODE button will make auto mode
operation.
※
When the batteries are removed, the setting will return to the
default setting (Auto mode is valid).
Instruct the customer to set the mentioned above when
replacing the batteries. (How to set is also mentioned in
the user’s manual attached on the air conditioner.)
Cooling test run operation
●
After safety confirmation, turn on the power.
●
Transmit a cooling operation command with wireless remote control, while the backup button on
the receiver is pressed.
●
If the backup button on the receiver is pressed during a test run, it will end the test run.
●
If you cannot operate the unit properly during a test run, please check by consulting with inspection
guides on the wiring diagram of outdoor units.
How to read the two-digit display
On the receiver of a wireless kit, a two-digit (7-segment) display is provided.
(1) An indication will be displayed for one hour after power on.
(2) An indication will be displayed for 3.5 seconds after transmitting a “STOP” command from the
wireless remote control or the operation of the backup button to stop the unit.
(3) An indication appearing in (1) or (2) above will go off as soon as the unit starts operation.
(4) When there are no error records to indicate, addresses of all the connected units are displayed.
(5) When there are some error records remaining, the error records are displayed.
(6) Error records can be cleared by transmitting a "STOP" command from the wireless remote
control, while the backup button is pressed.
Backup button
A Backup button is provided on the receiver.
Even when the operation from the wireless remote control
is not possible (due to flat batteries, controller lost, or
control failure), still it possible to operate as temporary
means. Press the button directly when operating it.
(1) The air conditioner starts the operation with the
condition of Auto mode, 23
˚
C of set point, High fan
speed and horizontal louver position.
(2) The air conditioner stops the operation when the button
is pressed when in operation.
backup button
How to install the receiver
Remote control
The receiver can be installed by replacing with a corner panel on the applicable decorative panel.
Preparation before installation
①
Attach the decorative panel onto the air conditioner according to the installation manual for
the panel.
②
Remove the air return grille.
③
Remove a corner panel located on the refrigerant pipes side.
④
Remove three screws and detach the cover (indicated as shadowed area) from the control
box of the air conditioner.
Setting on site
①
PCB on the receiver has the following switches to set the functions. Default setting is shown
with mark.
Customized signal setting to avoid
mixed communication
Receiver master/slave setting
Buzzer valid/Invalid
Auto restart
Normal
Remote
Master
Slave
Valid
Invalid
Valid
Invalid
Refrigerant pipes
Drain pipe
Fasten the wiring to the terminal securely and hold the cable securely so as not to apply
unexpected stress on the terminal.
Loose connection or hold will cause abnormal heat generation or fire.
●
Make sure the power supply is turned off when electric wiring work.
Otherwise, electric shock, malfunction and improper running may occur.
●
DO NOT install the wireless kit at the following places in order to avoid malfunction.
●
DO NOT leave the wireless kit without the cover.
In case the cover needs to be detached, protect the receiver with a packaging box or bag
in order to keep it away from water and dust.
(1) Places exposed to direct sunlight
(2) Places near heat devices
(3) High humidity places
(4) Hot surface or cold surface enough to
generate condensation
(5) Places exposed to oil mist or steam directly
(6) Uneven surface
(7) Places affected by the direct airflow of the
AC unit.
(8) Places where the receiver is influenced by
the fluorescent lamp (especially inverter
type) or sunlight.
(9) Places where the receiver is affected by
infrared rays of any other communication
devices
(10)Places where some object may obstruct the
communication with the remote control
2.5
1.1
Wireless remote control's operable area
①
Standard reachable area of the signal
[condition] Illuminance at the receiver: 300lux
(when no lighting is installed within 1m of the receiver in an ordinary office.)
Ceiling surface
Reachable area of the signal
②
Correlation between illuminance at the receiver
and reachable area of the signal in a plain view.
The drawing in the right shows the
correlation between the reachable area
of the signal and illuminance at the
receiver when the remote control is
operated at 1.1m high under the
condition of ceiling height of 2.5m.
When the illuminance becomes double,
the area is narrowed down to two thirds.
The receivable area of the
signal when the illuminance
at the receiver is 300lux
The receivable area of the
signal when the illuminance at
the receiver is 600lux
③
Installation tips when several receivers are installed close
Minimum distance between the indoor units which can avoid cross communication is 5m
under the condition of 300lux of illuminance at the receiver.
(When no lighting is installed within 1m of the receiver in an ordinary office )
Caution
DO NOT install it on the following places
1. Places exposed to direct sunlight
2. Places near heat devices
3. High humidity places
Radio interference prevention mode
Ensure the correct
polarity when
inserting.
Indoor unit (1)
Address (0)
Indoor unit (2)
Address (1)
Indoor unit (16)
Address
( F )
Receiver
(For the method of switching, please see
Setting on site
in the section of
②
How to install the receiver
in this manual.)
Auto mode operation setting
WARNING
CAUTION
For the installation method of the air conditioner itself, refer to the installation manual enclosed in the
package.
4. Hot surface or cold surface enough to generate
condensation
5. Places exposed to oil mist or steam directly.
6. Uneven surface
Attention
PJF012D010
Notes :
Following functions of FDT Type-F indoor unit series are not able to be set with this wireless remote control (RCN-TC-36W-E).
1. Individual flap control system
2. 4-fan speed setting (P-Hi/Hi/Me/Lo)
→
3-fan speed setting (Hi/Me/Lo)
12. OPTION PARTS
12.1 Wireless kit
(1) FDT series (RCN-T-36W-E)
