background image

EN-4

Viewing computer images (continued)

Adjust the image size by turning the zoom ring.

If necessary, adjust the focus and zoom again.

To stop projecting:

Press the POWER button on the projector or the OFF ( ) button on the remote control.

A confirmation message is displayed.
To cancel the procedure, leave the projector for a while or press the MENU button.

Press the POWER button on the projector or the OFF ( ) button on the remote control again.

The lamp goes out and the projector goes into a standby mode. In this standby mode, the STATUS indicator 
blinks green.

10. Wait about 90 seconds.

During this period of 90 seconds in the standby mode, the intake fan and exhaust fan rotate to cool the lamp.
The lamp can’t be lit again for 1 minute after turning off the projector for safety purpose. It will take another 1 
minute for the STATUS indicator to go out. If you want to turn on the projector again, wait until the indicator goes 
out, and then press the POWER button.
The air outlet fans rotate faster as the temperature around the projector rises.
Do not unplug the power cord while the STATUS indicator is blinking. Unplugging the power cord immediately 
after use may cause a lamp breakdown.
Though the fan makes loud sounds during cooling, such symptom is not a malfunction.

11. Unplug the power cord from the outlet.

The POWER indicator will go out.
If the power cord should be unplugged accidentally while either the air inlet fan or the air outlet fans are 
operating or the lamp is on, allow the projector to cool down for 10 minutes with the power off. To light the lamp 
again, press the POWER button. If the lamp doesn’t light up immediately, repeat pressing the POWER button 
two or three times. If it should still fail to light up, replace the lamp.
Cover the lens with the lens cap to protect it from dust. 

AUTO POSITION button

When the image supplied from the computer is displaced, carry out the following procedure.

Display a bright image (such as a full-screen display of the Recycle Bin window).
When the screen saver has been enabled, disable it.
Press the AUTO POSITION button.
The projector automatically makes optimum positional settings for the input signal.
If the image is not projected in the correct position even after you press the AUTO POSITION button several 
times, change the settings in the SIGNAL menu to put the image in the correct position. (See page 4.)
When you carry out this procedure with a dark image, the image may be displaced.

1.
.
.

When connecting to a notebook computer:

When the projector is connected to a notebook computer, images may not be projected in some cases. In such cases, 
set the computer so that it can output signals externally. The setting procedure varies depending on the type of the 
computer. See the instruction manual of your computer.

Example of the setting procedure for external output

Press the [Fn] key and any of the keys [F1] to [F1] at the same time. (The key to be pressed depends on the type of 
the computer you use.) 

Setting of the resolution

If the resolution of the computer doesn’t match with that of the projector, projected images may be obscured. Ensure 
that their resolutions are the same (see page 46). For the method to change the output resolution of the computer, 
contact the manufacturer of the computer. 

7.

8.


9.




Summary of Contents for HC4000

















































Reviews: