9
CALL OUT
setting
TAPE END
setting
WRNG•TAPE END
WRNG
STOP
Outputs a call signal at
the end of the tape
Outputs a call signal at the end
of the tape for 2 seconds
Outputs a call signal at the
end of the tape
When a malfunction occurs in the VCR
during recording, a call signal is output.
REWIND
REPEAT
ALARM
• PROT
When there are no
alarm recordings
during recording
When there are alarm
recordings during
recording
WRNG•REMAIN
Outputs 3 minutes before
the tape end
SETTING THE MENUS
<REAR TERMINAL>
WRNG•TAPE END
REC- 1
REC
SERIES
CALL OUT
CLOCK OUT
MODE OUT
REC IN
4
RECORDING MODE (REC MODE)
Sets the recording mode.
NORMAL<SP> : Choose when higher picture quality is preferred. With this setting, the recording time mode is switched in the order of
3H
}
L24H
}
48H
}
72H
}
96H
}
120H
}
168H
}
0H
}
3H ...
H•D<LP> :
Select a LP setting to perform High Density recording. This provides 2x more fields than Normal Density(SP). It
reduces the time interval between pictures, providing more pictures for smoother time lapse recording. With this
setting, the recording time mode is switched in the order of 6H
}
L18H
}
48H
}
72H
}
96H
}
120H
}
168H
}
0H
}
6H ...
5
SETTING THE NUMBER OF FIELDS IN ONE-SHOT RECORDING (ONE SHOT•FIELD)
Sets the number of recorded fields in the one-shot recording mode. When the JOG dial is turned to the right, the display will be
switched in the order of 1
}
2
}
3
}
4
}
5
}
10
}
20
}
30
}
1
}
....
6
SETTING THE INTERVAL TIME IN THE ONE-SHOT RECORDING MODE (ONE SHOT•INTERVAL)
Sets the interval time in the one-shot recording mode. When the JOG dial is turned to the right, the display will be switched in the
order of SHOT
}
10S (second)
}
15S
}
30S
}
45S
}
1M
}
2M
}
3M
}
SHOT
}
....
REAR TERMINAL
1
SETTING THE CALL SIGNAL OUTPUT AT THE END OF THE TAPE (CALL OUT)
Enables or disables the signal that is output from the CALL terminal when the end of the tape is
reached during recording. If any abnormalities occur during recording, a CALL signal is output from
the CALL terminal on the rear panel regardless of CALL OUT setting.
WRNG•TAPE END:
A signal is output at the end of the tape or when a malfunction occurs.
WRNG•REMAIN:
The signal is output when a malfunction occurs in this VCR or when the tape
has approximately 3 minutes left in 3H mode.
WRNG:
When a malfunction occurs in the VCR during recording, a CALL signal is output.
This is used in conjunction with TAPE END (FIRST TIME SET UP) to determine when the CALL signal is output as shown below.
2
SETTING THE FREQUENCY DIVISION RATIO (CLOCK OUT)
Sets the frequency division ratio of the CLOCK OUT terminal.
First, set the recording mode for the “CLOCK OUT” pulse output in the “REAR TERMINAL” menu.
REC:
When recording in any mode.
T/L-REC:
When recording in time lapse mode (L18H, L24H, 48H, 72H, 96H, 120H, 168H or 0H).
Second, select the frequency division ratio setting by turning the SHUTTLE ring. When the JOG dial is turned, the display will be
switched in the order of 1
}
2
}
3
}
4
}
5
}
10
}
15
}
20
}
25
}
30
}
50
}
60
}
F (field)
}
1
}
... The numbers from 1 to
60 indicate the number of frames in 3H or 6H recording mode or the number of fields in time lapse recording mode. (One frame
consists of two fields.) One field is selected when it is set to “F” (field).
3
SETTING THE OPERATION MODE OF THE MODE OUTPUT TERMINAL (MODE OUT)
Set the state in which the signal output at the MODE OUT terminal is switched to the active condition. When the JOG dial is turned,
the display will be switched on in the order of REC (recording)
}
PLAY (playback)
}
POWER (power “ON”)
}
TAPE IN (tape is
inserted)
}
TAPE REMAIN (3 minutes in 3H mode before the tape end)
}
CLOCK ADJ (output the signal for 1 second when the
clock indicates “00(min.):00(sec.)”)
}
REC.
4
SETTING THE OPERATION MODE OF THE REC IN TERMINAL (REC IN)
SERIES: Recording starts when the REC IN terminal is short-circuited to ground or a “L” level voltage (0 - +1.6V) is applied.
REC-START/ STOP: Recording starts when the REC IN terminal is short-circuited to ground or a “L” level voltage (0 - +1.6V) is
applied. Should this connection be removed, recording will stop.
SYNC REC: The video signal from 3 or 9 cameras can be recorded separately by connecting the switcher. (“SYNC REC” function
is available when recording in L18H or L24H mode.) Refer to “SYNCHRONOUS RECORDING” on page 16.
Summary of Contents for HS-7168E
Page 32: ...872C191D3 PRINTED IN JAPAN ...