background image

Document No.: E20-018-00 

 

 

5.2. 

Installing EJ-210 

5.2.1. 

Top of Control Box 

Use the four M6 screws supplied to mount the EJ-210 on top of the control box. 

 

(1)  Drill mounting holes in the position where the EJ-210 is mounted. 

Mounting dimensions:  115 mm × 350 mm (Refer to the overall view drawings.) 
Mounting screws: 

M6 × 4 (supplied) 

(2)  Open the top cover of the EJ-210. 
(3)  Use the M6 screws supplied to secure the EJ-210. 

NOTE 1:  Use only the screws supplied. If other screws are used, they may contact and 

damage the circuit board. 

NOTE 2:  Do not remove the rubber feet from the EJ-210. Removing the rubber feet may 

result in damage to the circuit board when the EJ-210 is installed. 

(4) When wiring is complete, close the top cover.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 5-1: Example of installation on top of the control box 

 

 

Control box 

M6

Boiler operation terminal EJ-210 
top cover 

Boiler operation terminal EJ-210 
main unit 

Machine 
screw 

Heat-resistant 
tube 

Front panel 

Plain washer 

Spring washer 

M6 screw 

Summary of Contents for EJ-210























Reviews: