background image

 Be sure to read the instructions in this section carefully before use.

 Make sure to observe the instructions in this manual as the conventions of safety symbols and messages

 

 

regarded as very important precautions are included.

 We also recommend you keep this instruction manual handy for future reference.

Safety Symbol and Message Conventions

Safety symbols and messages described below are used in this manual to prevent  bodily injury and  property 

damage which could result from mishandling.  Before operating your  product, read this manual first and

 

 

understand the safety symbols and messages so you are thoroughly aware of the potential safety 

Indicates a potentially hazardous situation which, if mishandled, could

result in death or serious personal injury.

Indicates a potentially hazardous situation which, if mishandled, could

result in moderate or minor personal injury, and/or property damage.

When Installing the Unit

• 

Do not expose  the unit to rain or an  environment

 

where it may be splashed by water or other liquids, 

as doing so may result in fire or electric shock.

 

• 

Use the unit only with the voltage  specified  on 

the

 

unit. Using a voltage higher than that which is

 

   

specified may result in fire or electric shock.

• 

Do not cut, kink, otherwise damage nor modify 

the

 

power  supply cord.  In addition, avoid using  

the

 

power cord in close proximity to heaters, and 

never

 

place heavy objects including the unit

 

itself 

on the  power cord, as doing so may result in fire 

or electric shock.

• 

Be sure to replace the unit's terminal cover after

 

 

connection completion. Because high voltage is

 

 

applied to the speaker terminals, never touch 

these terminals to avoid electric shock.

• 

Be sure to ground the safety ground (earth)

 

terminal to avoid electric shock. Never ground to a  

gas pipe as a catastrophic disaster may result.

• A

void installing or mounting the unit in unstable

 

 

locations, such as on a 

shaky

 table or a slanted

 

surface. Doing so may result in the unit falling

 

 

down, causing personal injury and/o

r

 property  

damage.

When the Unit is in Use

Should the following irregularity be found during    

use, immediately switch off the power, disconnect

 

   

the power supply plug from the AC outlet and    

contact your Mixhits Audio dealer. Do not

 

attempt to 

operate the unit in this condition as this may cause 

fire or electric shock. 

  

     

• 

If you detect smoke or an odor from the unit.

     

• 

If water or any metallic object gets into the unit

     

• 

If the unit falls, or the unit case breaks

     

• 

If the power supply cord is damaged.

     

• 

If it is malfunctioning (no sound.)

• 

To prevent a fire or electric shock, never open or    

remove the unit case as there are high voltage    

components inside the unit. Refer all servicing to    

your Mixhits Audio dealer.

• 

Do not place cups, bowls, or other containers of  

liquid or metallic objects on top of the unit. If they  

accidentally spill into the unit, this may cause a fire  

or electric shock.

• 

Do not insert 

or

 drop metallic objects or flammable  

materials in the ventilation slots of the unit's  cover,  

as

 

this may result 

i

n fire or electric shock.

1. SAFETY PRECAUTIONS

3

Summary of Contents for MRT-B120D















Reviews: