background image

 

 

Document No 50398-001   Rev F   02 Aug 2020

 

 

 

 

 

 

 

 

 

       

2

 of 

20

 

2

 of 

20

 

 

 

Dear Ophir-Spiricon Customer, 

 

Thank you for your recent purchase of the BeamWatch system. 

At Ophir-Spiricon we strive to provide the highest level of leading edge photonic measurement technology and service 
possible. We hope that your experience with us is a pleasant one, and anticipate the relationship we build will serve your 
photonic measurement needs for years to come. 

As a valued customer, your comments and opinions are always very important to us. If you have any concerns, questions, 
or comments, bring them to our 

service department’s attention. We are ready to help with everything from

 basic setup to 

working with you to find solutions for your most complex photonics measurement needs. 

Please let us know if there is any way we can be of service. Thank you once again for your business. 

Sincerely, 

Ophir-Spiricon, LLC 

 

 

Ophir-Spiricon, LLC 

3050 North 300 West 

North Logan, UT 84341, USA 

Tel 435-753-3729 

Fax 435-755-5231 

www.ophiropt.com/photonics

 

Summary of Contents for Ophir Spiricon BeamWatch Standard





















Reviews: