background image

 

Non-Contact  
Infrared Body Thermometer 

Model No: 70113

 

Instruction Manual 
Please read this instruction manual completely before operating. 

Package Contents 

 

Quantity 

1pc 
2pc 
1pc

 

 
Parts 

Non-Contact Infrared Body Thermometer 
1.5V (AAA) Batteries 
User Manual

 

Thermometer Specification 

 

Measurement Unit: 

Operating Mode: 

 

Recommended Measuring Site: 

Reference Body site: 

Rated Output Range: 

 

Range: 

 

Accuracy 

 

Display Resolution: 

Three-Color Backlight Display:  

 
 

Auto Power Off Time: 

Measuring Time: 

Measuring Distance: 

Stored Memory Capacity: 

Operating Condition: 

 

 
°C/°F 
Adjusted Mode (body mode) 
Direct mode (surface mode) 
Forehead 
Axillary 
Body mode: 95.0°F 

 107.6°F (35.

°C 

 42.0°C) 

Surface Mode: 32.0°F 

 212.0°F (0.0°C 

 100.0°C) 

Body Mode: 93.2°F 

 109.2°F (34.0°C 

 42.9°C) 

Surface Mode: 32.0°F 

 212.0°F (0.0°C 

 100.0°C) 

Body mode: +/- 0.4°F (0.2°C) 
Surface mode: +/- 3.6°F (2.0°C) 
0.1°C/ 0.1°F 
Green (Normal):

 

95.9°F 

 99.1°F (35.5°C 

 37.3°C)

 

Yellow (Mild Fever): 99.3°F 

 100.4°F (37.4°C 

 38.0°C)

 

Red (Fever): 100.6°F 

 109.2°F (38.1°C 

 42.9°C)  

< 18s 
< 2s 
1CM 

 5CM (0.4 

 2.0in) 

50 
Operating Temperature 59.0°F 

 95.0°F (15.0°C 

 35.0°C)  

Relative humidity 

≤85% Pressure 7۠Kpa –

 106Kpa 

Summary of Contents for 70113









Reviews: