background image

1

Copyright © 2019 by modkitsdiy.com

Use these instructions to learn:

How to build an effects pedal for overdrive.

The Thunderdrive Deluxe LTD is an overdrive pedal kit that will provide a strong clean signal boost in the 
early gain settings and smooth distortion at maximum gain settings. Adjusting output and distortion controls 
provides a wide variety of tones in spite of its simple construction. It is capable of overdriving the preamp 
section of your guitar amp or adding its own layer of distortion at lower volume. This version is equipped 
with a three position diode selector switch.

The switch offers three different settings and tones. The top position is the classic silicon clipping diodes 
used in the original Thunderdrive. The middle position gives you the lifted diode “turbo” sound from the 
Deluxe model. The bottom position is a new setting limited to this version using germanium diodes for a 
warm vintage distortion.

THE THUNDERDRIVE DELUXE LTD (K-956)

Unplug when not in use 

to save battery life.

OUTPUT

DISTORTION

DIODE SWITCH

LED

Warning:  This circuit was designed for use with a 9 VDC power supply only.

Signal Input

(From Guitar)

Signal Output
(To Amplifier)

Summary of Contents for K-956












Reviews: