background image

82

83

   Reboot

If you experience any odd behavior on your 008R (see Troubleshooting section), you can 
reboot the machine with this command: if the rest of the front panel stops responding, you 
should still be able to trigger the reboot by using screen controls.

If the software reboot fails, the LCD screen will say so and suggest a hardware reboot: in this 
case please make sure to leave the unit off for at least 60 seconds before powering it back up.

   Reset

If you experience any odd behavior on your 008R (see Troubleshooting section), you can reset 
parts of the operating system with the 3 options in this page.

1.  Network:

 this option resets all Network settings and it is very useful anytime you connect 

the 008R to a different router or in a different network configuration

2.  Preferences:

 this option resets all the Setting preferences to the original factory values

3.  Factory:

 this option triggers a complete factory reset: in detail, it resets all 008R settings, 

including the above Network and Preferences, as well as restoring the original factory 
sound banks. Please be careful when applying this, as you will lose all your saved patches 
that are in the factory banks.

Summary of Contents for 008R
















































Reviews: