background image

 

3

 

 

 

 

 

 

     

 

 

Before installing this electric storage water heater, check and ensure 
that  the  power  socket  is  reliably  grounded.  Otherwise,  this  water 
heater  cannot  be  installed  and  used  yet.  Do  not  use  the  extension 

cord if the power socket is damaged. Incorrect installation and use of 
this water heater may result in serious injuries and loss of property. 
 

Special Caution 
 

 

This  appliance  (water  heater)  is  not  intended  to  be  used  by 
persons  with  special  needs  for  their  physical,  sensory  or  mental 

capabilities,  or  lack  of  experience  and  knowledge  (including 
children),  unless  they  have  been  given  the  supervision  or 
instructions concerning the use of the appliance by a person who 

responsible  for  their  safety.  Children  should  be  supervised  to 
ensure that they are not playing with this water heater. 

 

The  wall  in  which  this  water  heater  is  installed  should  be  able  to 

bear  the  twice  bigger  load  than  the  weight  of  this  water  heater 
filled  fully  with  water  without  distortion  and  cracks.  Otherwise, 

other strengthening measures should be adopted. 

 

The  power  socket  must  be  earthed  (grounded)  reliably.  The 

installation height of the power socket should not be lower than 1.8 
m. The rated current of the socket should not be lower than 16A.  

 

The  power  socket  and  the  power  plug  should  be  kept  dry  to 

prevent electrical leakage. If the flexible power cord is damaged, a 
special  power  cord  that  is  provided  by  manufacturer  must  be 

selected,  and  replaced  by  professional  maintenance  personnel. 
Contact 

MODENA

 Customer Care for help. 

 

For  the  correct  operation  of  the  appliance,  it  is  necessary  to  pay 

attention that the maximum inlet water pressure is 0.75 MPa, and 
the minimum inlet water pressure is 0.1  MPa 

 

When using the water heater for the first time (or for the first use 
after maintenance), the water heater cannot be switched on until it 

has been filled fully with water. When filling the water, at least one 
of the outlet valves of the water heater must be opened to exhaust 
the air. This valve  can be closed after the  water  heater  has been 

filled fully with water. 

PART 1: IMPORTANT SAFETY INFORMATION 

Summary of Contents for ES 10 CS















Reviews: