background image

 

 

 

 

 

 

     

 

 

General Remark 

 

The  installation  and  maintenance  has  to  be  done  by  qualified 

professionals  or  authorized  technicians  of 

MODENA

MODENA

  is  not 

responsible  for  any  damage  or  malfunction  caused  by  wrong 
installation  or  the  failure  in  following  instructions  that  are  included  in 

this  manual  book.  For  more  information  regarding  to  installation  and 
maintenance guidelines in details, please refer to below chapters. 

 

Caution 

 

Before  installing  this  electric  storage  water  heater,  check  and  ensure 
that  the  power  socket  is  properly  functional  and  reliably  grounded. 
Otherwise,  this  electric  storage  water  heater  cannot  be  installed  and 

used yet. Do not use an extension cord if there is a problem with the 
power  socket.  Incorrect  installation  and  use  of  this  electric  water 
heater may result in serious injuries and loss of property. 

 

Special Caution 

 

 

If  the  supply  cord  is  damaged,  it  must  be  replaced  by 

MODENA

 

technicians, 

MODENA

 service agent or similarly qualified persons in 

order to avoid a hazard. 

 

The power socket must be 

grounded

 (earthed) reliably. The rated 

current  of  the  power  socket  should  not  be  lower  than  16A.  The 
socket and plug shall be kept dry to prevent electrical leakage. 

 

The installation height of the power socket shall not be lower than 
1.8 m.  

 

The  wall  in  which  the  water  heater  is  installed  should  be  able  to 
bear  the  twice  bigger  load  than  the  weight  of  this  water  heater 

filled  fully  with  water  without  distortion  and  cracks.  Otherwise, 
other strengthening measures shall be adopted. 
 

 

PART 1: IMPORTANT SAFETY INFORMATION 

Summary of Contents for ES 10A3




















Reviews: