15
Manual Controls
The fireplace has manual controls located next to the
toggle switch, in front of the glass on the top right
side of the viewing area.
Power On/Off button:
Press once, indicator light turns
off and fireplace power turns on. All functions
enabled. Press again, flame turns off and fireplace
goes to standby. NOTE: Long pressing this button
for 3 seconds places fireplace in RF pairing mode.
Heat Button:
Pressing heat button cycles the heater
and blower on/off. Settings: Heater and blower
OFF, Low Heat, and High Heat. Indicator light will
match according to status. NOTE: On US LPM, low
and high heat have the same heat output when
wired for 120 V. Long Press the heater button for 5
seconds to lock/unlock the heater.
Preset Color Button:
Press preset color button to
cycle through the 8 preset color options. This
changes color of all three zones: the flame, ember
bed and down light. Colors in order of appearance:
MF orange-red-orange-golden
orange-green-aqua-blue-magenta
Resetting button:
Clears any paired remotes/devices
from the fireplace. Once cleared you can pair a
new remote or wall touch control. This will also
un-pair any APP that was paired to the fireplace.
After long pressing the reset button for 3 seconds,
a beeping tone will be heard indicating that the
pairing codes have been cleared.
Buzzer Tone Change:
Long press the on/off and
preset color button at the same time to enter the
beeping tone cycle mode. Continue to long press
both buttons to cycle through the 4 tone options.
The tone will change every 2 seconds while releas-
ing the buttons will act as the selection of the tone.
The tones in order of appearance are; tone-1,
tone-2, tone-3, and silent mode.
WIFI REMOTE
Power
Powers unit On & Off.
Flame
This is the flame zone adjustment tab.
After pressing this tab, the color ring and
brightness bar can be adjusted.
Ember Bed
This is the ember bed zone adjustment
tab. After pressing this tab, the color ring
and brightness bar can be adjusted.
Downlight
This is the downlight zone adjustment tab.
After pressing this tab, the color ring and
brightness bar can be adjusted.
Sync
This is a synchronization selector, used to
synchronize the current color on the color
wheel to all of the zones (Flame/Ember
Bed/Downlight). Grayed out SYNC is
when synchronization is “OFF”. Green
SYNC is when synchronization is “ON”.
Color Wheel
This is the color adjustment wheel for all
zones. Keeping contact on the color circle,
the color of the selected zone will change
continuously base on where you have your
finger.
Temperature Read Out
The number in the color circle is the
built-in thermostat temperature reading of
the fireplace.
Brightness Control
Brightness adjustment, for all zones
depending on tab selected or if sync is on.
The brightness of the fireplace changes in
real time as the slider is moved.
Heat Control
Heat controls open a drop-down menu.
The menu displays off, low, and high. Can
be used without thermostat.
Thermostat Slider
Normally inactive while heater is “ON.” To
use the thermostat while the heater is
“ON,” activate the thermostat by setting
the slider to the desired temperature.
Note: Does not save when turned “OFF.”
NOTE:
When silent mode is selected, a tone will still
be present for performing system functions such
as remote pairing or Wi-Fi pairing.
Placing in Wi-Fi Paring Mode:
-EZ Mode:
While the fireplace is ON, long press
the Preset Color button for 3 seconds. An audible
beeping tone will sound and the flame light, ember
bed light, and down light will turn to white and
begin flashing rapidly. Fireplace is now in EZ
pairing mode, which lasts for 2 minutes.
-AP Mode:
While the fireplace is ON, long press
the Preset Color button for 6 seconds. Two audible
beeping tones will sound and then only the FLAME
LIGHTS and nothing else will turn to white and
begin flashing slowly. Fireplace is now in AP pairing
mode, which lasts for 2 minutes
.
NOTE:
Fireplace is also equipped with Bluetooth
pairing. There is no mode setting for the Bluetooth
as the APP will automatically detect the Bluetooth
signal for pairing when attempting to pair fireplace
to Bluetooth.
