background image

THIS MANUAL IS THE PROPERTY OF THE OWNER.  

PLEASE BE SURE TO LEAVE IT WITH THE OWNER WHEN YOU LEAVE THE JOB. 

Inspection on Arrival

1.  Inspect unit upon arrival. In case of damage, report it 

immediately to the transportation company and your local 

Modine sales representative.

2.  Check rating plate on unit to verify that power supply meets 

available electric power at the point of installation.

3.  Inspect unit upon arrival for conformance with description of 

product ordered (including specifications where applicable).

Table of Contents

Inspection on Arrival. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Special Precautions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SI (Metric) Conversion Factors  . . . . . . . . . . . . . . . . . . . . . . . . 3

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3

Unit Location  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

  Combustible Material and Service Clearances  . . . . . . . . . . 4

  Unit Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

   Venting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  6

  Venting & Condensate Drain  . . . . . . . . . . . . . . . . . . . . . . . 13

  Gas Connections  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

  High-Altitude Accessory Kit  . . . . . . . . . . . . . . . . . . . . . . . . 15

  Electrical Connections  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

 Ductwork. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Performance Data  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Service/Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Model/Serial Number/Replacement Parts . . . . . . . . . . . . . . . 31

Commercial Warranty. . . . . . . . . . . . . . . . . . . . . . . . Back Cover

InsTAllATIon And servICe mAnuAl

high efficiency, separated combustion gas-fired unit heaters 

models PTC and BTC

6-563.7

5H0807150000

November, 2014

®

Effinity

93

, Conservicore Technology, and any combination of 

these names either together or with other words is trademarked 

by Modine Manufacturing Co. 

All models approved for use in California by the CEC and in 

Massachusetts. Unit heater is certified for residential (size 110 

and smaller only) and commercial applications. 

WARNING

1.  Improper installation, adjustment, alteration, 

service, or maintenance can cause property 

damage, injury, or death and could cause 

exposure to substances which have been 

determined by various state agencies to 

cause cancer, birth defects, or other 

reproductive harm. read the installation, 

operating, and maintenance instructions 

thoroughly before installing or servicing 

this equipment.

2.  do not locate AnY gas-fired units in areas 

where chlorinated, halogenated, or acidic 

vapors are present in the atmosphere. 

These substances can cause premature 

heat exchanger failure due to corrosion, 

which can cause property damage, serious 

injury, or death.

FOR YOUR SAFETY

WHAT To do If You smell gAs:

1. open windows.

2. do not try to light any appliance.

3.  do not touch any electrical switch; do  

not use any phone in your building.

4.  extinguish any open flame.

5.  Immediately call your gas supplier from a 

neighbor’s phone. Follow the gas supplier’s 

instructions. If you can not reach your gas 

supplier, call your fire department. 

FOR YOUR SAFETY

The use and storage of gasoline or other 

flammable vapors and liquids in open containers 

in the vicinity of this appliance is hazardous.

ImpORTANT

The use of this manual is specifically intended 

for a qualified installation and service agency.  

All installation and service of these units 

must be performed by a qualified installation 

and service agency.

model PTC

Summary of Contents for 215BTC260

































Reviews: