Mohawk RJ-50-AH Series, Installation, Operation, Maintenance, Parts

MOHAWK MODEL RJ-50-AH-SERIES 

2

IMPORTANT NOTES FOR MOHAWK LIFT DEVICES 

 
RECOMMENDATIONS BY THE INDIVIDUAL USER OR USING 
ORGANIZATION FOR IMPROVING THIS PUBLICATION OR ANY 
ASPECT OF THE PRODUCT ARE ENCOURAGED AND SHOULD BE 
FORWARDED IN WRITING TO: 
 
 

MOHAWK RESOURCES LTD. 

 PRODUCT 

IMPROVEMENTS 

 65 

VROOMAN 

AVE. 

AMSTERDAM, NY, 12010 

 
THIS IS NOT A VEHICLE LIFTING PROCEDURE MANUAL AND NO 
ATTEMPT IS MADE OR IMPLIED HEREIN TO INSTRUCT THE USER 
IN LIFTING METHODS PARTICULARLY TO THE INDIVIDUAL 
APPLICATION OF THE EQUIPMENT DESCRIBED IN THIS MANUAL. 
RATHER, THE CONTENTS OF THIS MANUAL ARE INTENDED AS A 
BASE LINE FOR OPERATION, MAINTENANCE, TROUBLE 
SHOOTING, AND PARTS LISTING OF THE UNIT AS IT STANDS 
ALONE AND AS IT IS INTENDED AND ANTICIPATED TO BE USED 
IN CONJUNCTION WITH OTHER EQUIPMENT. 

PROPER APPLICATION OF THE EQUIPMENT DESCRIBED HEREIN 
IS LIMITED TO THE PARAMETERS DETAILED IN THE 
SPECIFICATIONS AND THE USES SET FORTH IN THE 
DESCRIPTIVE PASSAGES. ANY OTHER PROPOSED APPLICATION 
OF THIS EQUIPMENT SHOULD BE DOCUMENTED AND 
SUBMITTED IN WRITING TO MOHAWK RESOURCES LTD. FOR 
EXAMINATION. THE USER ASSUMES FULL RESPONSIBILITY FOR 
ANY EQUIPMENT DAMAGE, PERSONAL INJURY, OR ALTERATION 
OF THE EQUIPMENT DESCRIBED IN THIS MANUAL OR ANY 
SUBSEQUENT DAMAGES. 

DO NOT WELD, APPLY HEAT, OR MODIFY THIS EQUIPMENT IN ANY 

MANNER WITHOUT WRITTEN AUTHORIZATION FROM

 MOHAWK 

RESOURCES LTD.

CERTAIN ALLOY OR HEAT-TREATED 

COMPONENTS MAY BE DISTORTED OR WEAKENED, RESULTING IN 
AN UNSAFE CONDITION. 

 
MOHAWK RESOURCES LTD.

IS NOT RESPONSIBLE FOR 

DISTORTIONS, WHICH RESULT FROM WELDING ON THIS 
EQUIPMENT AFTER MANUFACTURING IS COMPLETED. 
UNAUTHORIZED WELDING, APPLICATION OF HEAT, OR 

MODIFICATION OF THIS EQUIPMENT VOIDS ANY AND / OR ALL 
APPLICABLE WARRANTIES COVERING THIS EQUIPMENT. 

ALL WARRANTIES APPLICABLE TO THIS EQUIPMENT ARE 
CONTINGENT ON STRICT ADHERENCE TO THE MAINTENANCE 
SCHEDULES AND PROCEDURES IN THIS MANUAL. 
 
KEEP ALL SHIELDS AND GUARDS IN PLACE. INSURE ALL SAFETY 
MECHANISMS ARE OPERABLE. KEEP HANDS, FEET, AND 
CLOTHING AWAY FROM POWER-DRIVEN AND MOVING PARTS. 

CAUTION

THE EQUIPMENT DESCRIBED IN THIS MANUAL COULD BE 
POTENTIALLY DANGEROUS IF IMPROPERLY OR CARELESSLY 
OPERATED. FOR THE PROTECTION OF ALL PERSONS AND 
EQUIPMENT, ONLY COMPETENTLY TRAINED OPERATORS WHO 
ARE CRITICALLY AWARE OF THE PROPER OPERATING 
PROCEDURES, POTENTIAL DANGERS, AND SPECIFIC 
APPLICATION OF THIS EQUIPMENT SHOULD BE ALLOWED TO 
TOUCH THE CONTROLS AT ANY TIME. 
 
SAFE OPERATION OF THIS EQUIPMENT IS DEPENDENT ON USE, 
IN COMPLIANCE WITH THE OPERATION PROCEDURES OUTLINED 
IN THIS MANUAL ALONG WITH THE MAINTENANCE AND 
INSPECTION PROCEDURES WITH CONSIDERATION OF 
PREVAILING CONDITIONS. 
 
THE EQUIPMENT DESCRIBED IN THIS MANUAL IS NEITHER 
DESIGNED NOR INTENDED FOR ANY APPLICATION ALONE OR IN 
CONJUNCTION WITH ANY OTHER EQUIPMENT THAT INVOLVES 
THE LIFTING OR MOVING OF 

PERSONS. 

 
ALWAYS CONSULT THE VEHICLE LIFTING GUIDE FOR THE 
PROPER LIFTING POINTS ON ANY VEHICLE. THESE GUIDES ARE 
AVAILABLE FROM THE VEHICLE MANUFACTURERS. 
AFTER LIFTING THE VEHICLE TO THE DESIRED HEIGHT, 
ALWAYS LOWER THE UNIT ONTO THE MECHANICAL SAFETIES. 
THE FORMING OF GOOD OPERATIONAL WORK HABITS WILL 
ELIMINATE OVERSIGHTS IN THE USE OF PROVIDED SAFETY 
DEVICES.

RJ-50-AH-SERIES JACKING BEAMS: 

Only certified RJ-50-AH-Series Jacking Beams are intended for use on certified versions of the Mohawk 
Parallelogram Lifts (see list below). Follow load rating of beam dependant on what lift it is on. Use of non-
certified jacking beams on certified lifts will void the certification of the lift. 

RJ-50P-Series Jacking Beams for use on the following certified lifts: 
Model RJ-50-AH-50000:

 Rated 50,000 Lb on 75k Lb Lifts (4 Post) 

Model RJ-50-AH-37500-P: 

Rated 37,500 Lb on 75-100k Lb Lifts (Parallel) 

Model RJ-50-AH-35000:

 Rated 35,000 Lb on 50k Lb Lifts (4 Post) 

Model RJ-50-AH-35000-P:

 Rated 35,000 Lb on 50k Lb Lifts (Parallel) 

Model RJ-50-AH-31500-P:

 Rated 31,500 Lb on 45k Lb Lifts (Parallel) 

Model RJ-50-AH-28000-P:

 Rated 28,000 Lb on 40k Lb Lifts (Parallel) 

Model RJ-50-AH-25000-P:

 Rated 25,000 Lb on 36-38k Lb Lifts (Parallel) 

Model RJ-50-AH-24500:

 Rated 24,500 Lb on 35k Lb Lifts (4-Post) 

Model RJ-50-AH-23000:

 Rated 23,000 Lb on 33k Lb Lifts (4-Post) 

Model RJ-50-AH-20000:

 Rated 20,000 Lb on 30k Lb Lifts (4-Post) 

Use of a pair of Jacking Beams is allowable, but the minimum distance between centerline of the beams (cylinders) is

14 ft min.

Loading of the jacking beams or combinations of jacking beams above the rated capacity of the lift itself could result in personal 
injury to the operator and/or damage to the lift and/or vehicle. The load rating of any jacking beam or combination of jacking beams 
on this unit must not exceed the rated capacity of the lift.