background image

1.   Read all instructions before using this heater.

2.   This heater will get very hot while in use .To 
      avoid burning, do not let bare skin touch hot 
      surface. Keep flammable materials, such as
      furniture, pillows, bedding, papers, cloths and
      curtains at least 3 feet from the heater.

3.   DO NOT LEAVE heater unattended.  Extreme 
      caution is necessary when any heater is used 
      by, or near ,children or disabled persons, and 
      whenever the heater is left operating and 
      unattended.

4.   Always unplug heater when not in use.

5.   Do not operate any heater with a damaged 
      cord or plug, if the heater malfunctions, or has 
      been dropped or damaged in any manner. 
      Return heater to authorized service facility for 
      repairs.

6.   

7.   Never operate heater near water or where it 
      can be knocked over.

8.   Do not run cord under carpeting. Do not cover
      cord with throw rugs, runners, or similar
      coverings. Arrange cord away from traffic area 
      and where it will not be tripped over.

9.   To disconnect heater ,remove plug from 
      electrical outlet.

10. Connect to properly grounded outlets only.

11. Do not insert or allow foreign objects to enter
      ventilation or exhaust opening; doing so may
      cause an electrical shock or fire, or may 
      damage the heater.

Can be used indoors or outdoors. Operate at 

      least 3 feet from people or objects

12. To Prevent a possible fire, do not block air 
      intakes or exhaust in any manner. Do not use
      on soft surfaces, like a bed ,where openings 
      may become blocked.

13. A heater has hot and sparking parts inside. Do 
      not use it in area where gasoline, paint, or 
      flammable liquids are used or stored.

14. Use this heater only as described in this 
      manual. Any other use not recommended by 
      the manufacturer may cause fire, electrical 
      shock or injury to persons.

15. Avoid the use of an extension cord because 
      the extension cord may overheat and cause a 
      risk of fire. However, if you have to use an 
      extension cord, use either a 12 or 14 gauge 
      wire which is rated not less then 1900 watts. 
      The recommended length for a 14 gauge wire
      is  0-50 feet. IF a longer cord is needed,use a 
     12 gauge wire no longer than 100 feet

16. SAVE THESE INSTRUCTIONS for future 
     reference.

17. Please keep each side of the head unit at 
      least 12 inches from the objects.[Please see 
      the below illustration].

Summary of Contents for 60411











Reviews: