background image

Addendum to User Manual - Wireless STAR & eNode 

 

       

 

 

Page 

8

 of 

9

 

 

 

Mojix Incorporated 

www.mojix.com 

Appendix F: FCC Notice 

 
INSTRUCTION TO THE USER  
 
The user is cautioned that changes or modifications not expressly approved by the party 
responsible for compliance could void the user’s authority to operate this equipment. 
 
INSTRUCTION TO THE USER  
 
This equipment has been tested and found to comply with the limits for a class B digital 
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency energy and if not installed 
and used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one or more of the following 
measures: 
 

  Reorient or relocate the receiving antenna. 

  Increase the separation between the equipment and receiver. 

 Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected. 

  Consult the dealer or an experienced radio/TV technician for help. 

 
This equipment has been certified to comply with the limits for a class B computing 
device, pursuant to FCC Rules. In order to maintain compliance with FCC regulations, 
shielded cables must be used with this equipment. Operation with non-approved 
equipment or unshielded cables is likely to result in interference to radio and TV 
reception. The user is cautioned that changes and modifications made to the equipment 
without the approval of manufacturer could void the user's authority to operate this 
equipment. 
 

CAUTION: To comply with FCC RF exposure compliance requirements, a separation 
distance of 20 cm must be maintained between the antenna of this device and all persons. 

Summary of Contents for eNode










Reviews: