background image

Hand Crimp Tool for Board-In Crimp Terminals 

Doc No: ATS-6382569HM 

Release Date: 07-25-12 

UNCONTROLLED COPY

 

Page 5 of 6 

Revision: A 

Revision Date: 07-25-12 

MODULAR 

CRIMP 

HEAD 

BATTERY 

POWER 

CRIMP 

ADAPTER 

LOCKING 

PINS 

LOCKING PINS 

BATTERY 

POWERED 

TOOL

 

AIR 

POWER 

TOOL 

MODULAR 

CRIMP HEAD 

LOCKING 

PINS 

LOCKING 

PINS 

AIR POWER 

CRIMP 

ADAPTER 

 

5.

 

Pull force should be used as the final criteria for an acceptable crimp.  Pull force is measured with no 
influence from the insulation crimp.  The insulation should be stripped long (1/2 in.) so the insulation grips 
on the terminal do not grip the wire insulation or the conductor.  Refer to Molex Quality Crimping 
Handbook 63800-0029 for additional information on crimping and crimp testing. 

6.

 

Molex does not certify crimp hand tools. 

 

CAUTION

:  Molex crimp specifications are valid only when used with Molex terminals and tooling. 

 

Applications for the Modular Crimp Head 

 

WARNING

NEVER

 

operate, service, install, or adjust this Modular Crimp Head without proper instruction 

and without first reading and understanding the instructions in the proper Manual or Specification Sheet.  
See Chart below for the correct Manual or Specification Sheet. 

 

WARNING

NEVER

 

install tooling or service this tool while it is into any power source.  Disconnect the 

power by unplugging or turn off the Actuator from its power source. 

 

CAUTION: 

Keep fingers away from the crimping area when operating this tool.  It may cause severe injury. 

 

CAUTION: 

Wear safety glasses when operating or serving this tool. 

 
The chart below shows all applications for this Modular Crimp Head. 
 

Modular Crimp Head 

Order No. 

Tool 

Order no. 

Tool 

Description 

Adapter 

Order No. 

Adapter 

Description 

Figure No. 

63825-6970 

63816-0000  Hand Crimp Frame (Short) 

N/A 

N/A 

63816-0050  Hand Crimp Frame (Long) 

N/A 

N/A 

63816-0200  Battery Power Tool (110 V)  63816-0600  Battery Power Crimp Adapter 

63816-0250  Battery Power Tool (220 V)  63816-0600  Battery Power Crimp Adapter 

63816-0100 

Air Power Tool 

63816-0700 

Air Power Crimp Adapter 

 

Applications for the Modular Crimp Head 

Hand Crimp Tool 

Battery Powered Tool 

Air Powered Tool 

 

 

 

Figure 6 

Figure 7 

Figure 8 

MODULAR 

CRIMP 

HEAD 

LOCKING 

PINS 

HAND CRIMP 

FRAME LONG 

OR SHORT 

Summary of Contents for 63825-6900







Reviews: