molex 63825-9700 Quick Start Manual Download

Page: 6 / 6

Hand Crimp Tool for 1.50mm (.059") Pico-SPOX Crimp Terminals

Doc. No: ATS-6382597HM Release Date: 05-06-13

UNCONTROLLED COPY

Page 6 of 6

Revision: B

Revision Date: 04-26-18

PARTS LIST

Hand Crimp Tool 63825-9700

Item

Order Number

Description

Quantity

63816-0000

Hand Crimp Frame (Short)

63825-9775

Locator

63816-0001

Locking Pin

63600-0525

Handle Spring

63600-0520

Crimping Spring

Application Tooling Support

Phone:

(402) 458-TOOL (8665)

E-Mail:

applicationtooling@molex.com

Website:

www.molex.com/applicationtooling

Molex is a registered trademark of Molex, LLC in the United States of America and may be registered in other countries; all other

trademarks listed herein belong to their respective owners.

HANDLE

SPRING

RATCHET

RELEASE LEVER

LOCATOR

M4 X 8mm

LONG BHCS

Figure 9

CRIMPING

SPRING (2)

Summary of Contents for 63825-9700







Search results

Summary of Contents for 63825-9700

Reviews:

Related manuals for 63825-9700

Brands by name

Popular brands

molex 63825-9700, Quick Start Manual

Search results

Summary of Contents for 63825-9700

Reviews:

Related manuals for 63825-9700

Brands by name

Popular brands