AT 2200 Air Head Crimp Tool
Doc. No. 64005-1500
Release Date: 01-16-03
UNCONTROLLED COPY
Page 2 of 7
Revision: C
Revision Date: 01-10-06
TERMINAL
FRONT EDGE
OF BARREL
SAFETY
SHIELD
PUSH UP
Figure 1
LOCATOR
JAWS
OPEN
Wire Size: 10 – 12 AWG 5.00 – 3.00 mm²
Terminal
Wire Strip Length Insul. Dia. Max.
Terminal No.
Eng No. (REF)
In
mm
In
mm
19073-0181 C-830-10X .375 9.53 .250 6.35
19073-0182 C-830-10XLBK .375 9.53 .225 5.92
19073-0185 C-830-10XX .375 9.53 .326 8.13
19073-0188 C-830-14 .375 9.53 .225 5.72
19073-0191 C-830-14X .375 9.53 .250 6.35
19073-0192 C-830-14XLBK .375 9.53 .225 5.92
19073-0195 C-830-14XX .375 9.53 .326 8.13
19073-0200 C-830-56 .375 9.53 .225 5.72
19073-0202 C-830-56X .375 9.53 .250 6.35
19073-0203 C-830-56XLBK .375 9.53 .225 5.92
19073-0206 C-830-56XX .375 9.53 .326 8.13
19073-0216 C-836-06 .375 9.53 .225 5.72
19073-0220 C-836-06X .375 9.53 .250 6.35
19073-0222 C-836-08 .375 9.53 .225 5.72
19073-0225 C-836-08X .375 9.53 .250 6.35
19073-0227 C-840-10 .375 9.53 .225 5.72
19073-0229 C-840-10X .375 9.53 .250 6.35
19073-0231 C-840-14 .375 9.53 .225 5.72
19073-0233 C-840-14X .375 9.53 .250 6.35
19073-0236 C-840-38 .375 9.53 .225 5.72
19073-0238 C-840-38X .375 9.53 .250 6.35
19073-0242 C-840-56 .375 9.53 .225 5.72
19073-0244 C-840-56X .375 9.53 .250 6.35
19073-0272 C-830-10XXBK .375 9.53 .326 8.13
19073-0273 C-830-14XXBK .375 9.53 .326 8.13
19073-0274 C-830-56XXBK .375 9.53 .326 8.13
19081-0005 C-5006-MS .375 9.53 .225 5.72
19090-0083 C-212-08X .375 9.53 .250 6.35
19090-0085 C-212-10X .375 9.53 .250 6.35
19099-0044 C-2710-06X .375 9.53 .225 5.72
19099-0048 C-2718-08X .375 9.53 .225 5.72
19099-0050 C-2719-10X .375 9.53 .225 5.72
19115-0033 C-8196-06 .375 9.53 .225 5.72
19115-0035 C-8197-08 .375 9.53 .225 5.72
19115-0037 C-8198-10 .375 9.53 .225 5.72
19115-0039 C-8199-14 .375 9.53 .225 5.72
Wire Size: 10 – 12 AWG 5.00 – 3.00 mm²
Terminal
Wire Strip Length Insul. Dia. Max.
Terminal No.
Eng No. (REF)
In
mm
In
mm
19115-0041 C-8710-05 .375 9.53 .225 5.72
19115-0042 C-8710-06 .375 9.53 .225 5.72
19115-0046 C-8718-08 .375 9.53 .225 5.72
19115-0048 C-8719-10 .375 9.53 .225 5.72
19127-0086 C-817-08 .375 9.53 .225 5.72
19127-0089 C-817-10 .375 9.53 .225 5.72
19139-0060 C-8105-08 .375 9.53 .225 5.72
19144-0037 C-241-06X .375 9.53 .250 6.35
19144-0039 C-241-08X .375 9.53 .250 6.35
19144-0042 C-241-10X .375 9.53 .250 6.35
19144-0046 C-268-14X .375 9.53 .250 6.35
19154-0028 C-246X .225 5.95
.225
5.72
19154-0037 CS-V-346X .281 7.14 .225 5.72
19183-0019 C-811-10 .375 9.53 .225 5.72
19198-0039 C-8105-06 .375 9.53 .225 5.72
19198-0044 C-841-06 .375 9.53 .225 5.72
19198-0047 C-841-08 .375 9.53 .225 5.72
19198-0050 C-841-10 .375 9.53 .225 5.72
19198-0056 C-868-14 .375 9.53 .225 5.72
19198-0057 C-868-14X .281 7.14 .250 6.35
19204-0025 C-2XCX .375 9.53
.225
5.72
19204-0026 C-2YCX .375 9.53
.225
5.72
19204-0029 C-5XC .375
9.53
.225
5.72
19204-0030 C-5YC .375
9.53
.225
5.72
19206-0010 CS-V-303X .281 7.14 260 6.60
19212-0001 WP-2210X .281 7.14 .250 6.35
19213-0007 WP-8210 .281 7.14 .225 5.72
STEP DOWN BUTT SPLICE
Wire Size: 10 – 12 AWG 5.00 – 3.00 mm²
to 14 -16 AWG 2.00-1.30 mm²
Terminal
Wire Strip Length Insul. Dia. Max.
Terminal No.
Eng No. (REF)
In
mm
In
mm
19154-0035 CB-646X .281 7.14 .260 6.60
OPERATION
Refer to the instruction manual for the 19279-0001 (AT-200) for mounting this
crimp tool head.
Crimping Terminals
1. Adjust the locator up or down until the terminal being run sits flat and straight
in the tool.
2. Insert the wire into the terminal. Push up on the locator blade and push the
terminal and wire with the barrel facing up into the color-coded nest with front
edge of the barrel against the locator (See Figure 1). Release the locator blade
to hold the terminal in position.
Caution:
Never operate this tool without the supplied safety shield in place. Never place fingers in the tool nests.
