AT-2212 Air Crimp Tool Head
Doc No: ATS-640053600
Release Date: 06-24-03
UNCONTROLLED COPY
Page 3 of 8
Revision: B
Revision Date: 09-30-05
Wire Combinations for Nylon
Insulated Closed End Connectors
Part No. 191600009 (NC-2212)
Wire Type
Wire Gauge (AWG)
Rating
14 16 18 20 22
Stranded or Solid
2
3
1
UL & CSA
Stranded or Solid
2
1
2
UL & CSA
Stranded or Solid
2
1
3
UL & CSA
Stranded or Solid
1
1
UL & CSA
Stranded or Solid
1
2
UL & CSA
Stranded or Solid
1
3
UL & CSA
Stranded or Solid
1
4
UL & CSA
Stranded or Solid
1
5
UL & CSA
Stranded or Solid
1
1
UL & CSA
Stranded or Solid
1
2
UL & CSA
Stranded or Solid
1
3
UL & CSA
Stranded or Solid
1
4
UL & CSA
Stranded or Solid
1
5
UL & CSA
Stranded or Solid
1
1
1
UL & CSA
Stranded or Solid
1
2
1
UL & CSA
Stranded or Solid
1
3
1
UL & CSA
Stranded or Solid
1
4
1
UL & CSA
Stranded or Solid
1
1
2
UL & CSA
Stranded or Solid
1
1
3
UL & CSA
Stranded or Solid
1
1
4
UL & CSA
Stranded or Solid
1
2
2
UL & CSA
Stranded or Solid
1
2
3
UL & CSA
Stranded or Solid
1
3
2
UL & CSA
Stranded or Solid
6
UL & CSA
Stranded or Solid
5
UL & CSA
Wire Combinations for Nylon
Insulated Closed End Connectors
Part No. 191600009 (NC-2212)
Wire Type
Wire Gauge (AWG)
Rating
14 16 18 20 22
Stranded or Solid
5
1
UL & CSA
Stranded or Solid
4
UL & CSA
Stranded or Solid
4
1
UL & CSA
Stranded or Solid
4
2
UL & CSA
Stranded or Solid
3
UL & CSA
Stranded or Solid
3
1
UL & CSA
Stranded or Solid
3
2
UL & CSA
Stranded or Solid
3
3
UL & CSA
Stranded or Solid
2
UL & CSA
Stranded or Solid
2
1
UL & CSA
Stranded or Solid
2
2
UL & CSA
Stranded or Solid
2
3
UL & CSA
Stranded or Solid
2
4
UL & CSA
Stranded or Solid
1
1
UL & CSA
Stranded or Solid
1
2
UL & CSA
Stranded or Solid
1
3
UL & CSA
Stranded or Solid
1
4
UL & CSA
Stranded or Solid
1
5
UL & CSA
Stranded or Solid
6
UL & CSA
Stranded or Solid
5
UL & CSA
Stranded or Solid
4
UL & CSA
Stranded or Solid
3
UL & CSA
Stranded or Solid
2
UL & CSA
Crimping Terminals
1.
Hold air crimp tool with the locator as shown in Figure 1.
Insert the closed end connector in the locator slot. Make
sure that the shoulder of the connector is resting on the
locator plate. The connector should fit snugly into the jaws
of the crimp tool. See Figure 1.
2.
If necessary, adjust the jaws of the tool in the open position
so that the connector does not move or fall out of the jaws.
Using a 3/32” Allen wrench turn the adjusting screw in the
adjustment block clockwise (CW) to close the jaws. Turn
the adjusting screw counterclockwise (CCW) to open the
jaws. See Figure 2.
3.
Place pre-twisted wire into closed-end connector. Than
press lever (trigger) on air tool. See Figure 3. Release the
lever after jaws have fully closed
Caution:
Never place fingers in the tool nests.
Figure 1
JAWS OPEN
LOCATOR
PRE-TWISTED
WIRE
ADJUSTMENT
BLOCK
CONNECTOR
