molex CS 150 Instruction Manual Download

Page: 21 / 21

CS 150 Battery Crimping Tool

Doc No: ATS-638160200

Release Date: 12-06-07

UNCONTROLLED COPY

Page 21 of 21

Revision: A

Revision Date: 12-06-07

6.2 Troubleshooting

Make sure the battery is charged before toubleshooting this tool.

Symptom

Cause Solution

Dirt, contaminants, etc.,

in ram area of tool.

Clean the crimping tool.

Battery unit contacts corroded.

Clean contacts with pencil eraser or
contact cleaner

Battery unit contacts damaged.

Reform the contacts.

Tool is

inoperative.

Tool parts worn or damaged.

Contact a Molex representative.

Oil level is low.

Contact a Molex representative.

Dies stop

during operation.

Air in Hydraulic system.

Pull the trigger and hold the retract slide
simultaneously for about 10 seconds.

LED glows for

20 seconds.

Battery charge is low.

Charge or replace battery unit.

Crimping Tool

loses oil.

Damage to the internal seal.

Contact a Molex representative

Americas Headquarters
Lisle, Illinois 60532 U.S.A.
1-800-78MOLEX
amerinfo@molex.com

Far East North Headquarters
Yamato, Kanagawa, Japan
81-462-65-2324
feninfo@molex.com

Far East South Headquarters
Jurong, Singapore
65-6-268-6868
fesinfo@molex.com

European Headquarters
Munich, Germany
49-89-413092-0
eurinfo@molex.com

Corporate Headquarters
2222 Wellington Ct.
Lisle, IL 60532 U.S.A.
630-969-4550
Fax: 630-969-1352

Visit our Web site at http://www.molex.com

Summary of Contents for CS 150






















Search results

Summary of Contents for CS 150

Reviews:

Related manuals for CS 150

Brands by name

Popular brands

molex CS 150, Instruction Manual

Search results

Summary of Contents for CS 150

Reviews:

Related manuals for CS 150

Brands by name

Popular brands