background image

Monarch GC340 / 440 Owner’s Manual.  © Scooters Australia 201

0-13

17 

 

 

WARNING: Do not sit in or attempt to move your scooter unless the frame and rear carriage 
are securely engaged. Accidental separation of the frame from the rear carriage may occur 
and cause injury of damage. 

 

REINSTALL THE SEAT. 

1. Make certain that the seat post is mounted in the seat post pedestal and adjusted to 

the desired height. 

2. Raise and hold the seat swivel lever and then lift seat and position the seat swivel post 

into the seat post. See Fig. 18. 

3. Push down on the seat to make certain that the seat swivel post is fully inserted and 

locked. See Fig. 19. 

WARNING: Failing to assure proper installation of the seat could result in injury. 

 

REINSTALL THE ARMRESTS. 

1. Insert the right arm into the arm bracket.  
2. Tighten the right arm bracket adjustment knob. 
3. Insert the left arm into the arm bracket. 
4. Tighten the left arm bracket adjustment knob. 

Your scooter is now successfully assembled. 

SEAT SWIVEL LEV 

 
 
 
 
 
 
 
 
 
 
 
 
 

 

TRANSPORTING 

 

To Transport Your scooter: 

  Disassemble or fold down the seat and tiller (see section VII. “Disassembly”) as close 

as possible to the loading area of the vehicle to be used for transporting your scooter. 

o

  The degree to which you disassemble your scooter or fold the seat and tiller 

depends on the size and shape of the cargo area of the transporting vehicle. 

  Do not lift your scooter by its plastic body parts or tiller. Breakage of these parts is not 

covered by the warranty. 

  Do not use the tyres or wheels to lift the rear carriage. The carriage may rotate and 

cause injury or damage. 

  Moving blankets or other forms of padding may be used to protect your scooter during 

transportation. 

 

WARNING: If your scooter and its components are not properly and securely stowed during 
transportation, the scooter or the components may move or become airborne and cause 
injury or damage. 

 

WARNING: Never sit on your scooter when it is being transported. Always fasten down your 
scooter securely with an approved tie-down system while transporting your scooter. 

 

 

 

 

Figure 18. 

 
 

Figure 19. 

 
 

Summary of Contents for GC 340



























Reviews: