Mondial Designs Limited HB095 2008 Owner'S Handbook Manual Download

Page: 60 / 75

equipment details

5. Slide the holding tank into position through

access door (fig. 5).

6. Make sure the holding tank is secured by

the retaining clip. (fig. 6).

7. Open the waterfill door and add 50 ml of

Aqua Rinse. Aqua Rinse results in a better
flush and improves the hygiene of the

toilet. Then fill the watertank with fresh
water using a jerrycan or a hose. Tank
capacity is 7 litres (fig. 7).

operation

8. Turn the bowl in the most comfortable

position (fig. 8).

c-200 cw only: Before using the toilet it is
recommended to flush some water into the
bowl by lifting and pressing down the flush

handle (fig. 9).

9a.

c-200 cwe & cS only: Before using the
toilet it is recommended to flush some

water into the bowl by pressing and

releasing the flush button (fig. 9a).

10. The toilet may be used with the blade open

or closed. Pull valve handle towards you to
open (fig. 10).

11.

c-200 cw only:

After use, open valve

blade (if still closed) and flush, lift the flush

handle and press it down (fig. 11). After

flushing, close the blade by turning the

blade handle.

11a.

c-200 cwe & cS only:

After use, open

valve blade (if still closed) and flush, press
the flush button (fig. 11a).

After flushing, close the blade by turning the

blade handle.
The waste holding tank is located underneath
the toilet and is removed for emptying from
the outside of the vehicle through an access
door. A rotating pour out spout, automatic
holding tank vent, air release valve, valve
blade, carrying handles and hand grip are
incorporated in the waste holding tank. A
sliding cover guarantees optimal hygiene.

emptying the Holding tank

The holding tank capacity is approx. 17 litres
and the tank should be emptied when the
waste-level indicator lights up. The waste-
level indicator lights up when the holding tank
contains more than 15 litres of waste.

cautIon: do not allow the holding tank
to become overfilled. See trouble shooting
section for emergency emptying procedure.

12. Open access door and remove the holding

tank. The holding tank can only be removed
when the valve blade is closed (fig. 12).

13. Carry the holding tank to a normal

household type toilet or other authorised
disposal point. Place the holding tank in
vertical position and rotate pour out spout
upwards (fig. 13).

14. Remove the spout cap. Grasp unit by

upper carrying handle nearest to pour
out spout. Place other hand on upper
rear hand grip so that vent button can be
depressed with the thumb while emptying.

This ensures a smooth outflow of the tank

contents. (fig. 14).

Note: Only depress the vent button when

pour out spout is pointed downwards.

Rinse the holding tank with clean water. For

preparing for use again, see steps 1 to 7.

cleaning and maintenance

The lipseal and the seal of the automatic vent
are made of rubber and therefore these parts
need regular maintenance (depending on
frequency of use, once or twice a month).

tHetford caSSette toILet

cassette c-200 cw and c-200 cwe &
c-200cS

The toilet section of the C-200 includes a
rotatable bowl, removable seat and cover,

a console with a flush handle/flush buttons,
a built in flush-watertank and a waste level

warning indicator. The valve blade handle is
located underneath the bowl.

preparing for use

1. Open access door pull retaining clip

upwards (fig. 1).

2. Remove holding tank by pulling straight out.

When holding tank hits the stop, tilt front
end downwards slightly and remove (fig. 2).

3. Position tank vertically and swivel pour out

spout upwards (fig. 3).