SmartSELECT Merchant Operating Manual v 2.0
109
Private Label Transactions
To set up a Third Party Card
From the Idle screen:
1. Press
Menu
. The
Financial Transactions
menu appears.
2. Press
Config
. The
Terminal Configuration
menu appears.
3. Scroll down and select
Third Party Card
. The
Select Card Name or Press
Enter for New Card
prompt appears.
4. Press
Enter
. The
Enter Card Name
prompt appears with an alphanumeric key-
pad.
5. Key in the name (min. 2, max. 12 characters including spaces) of the Third
Party Card and press
Enter
. The
Select Card Name or Press Enter for New
Card
prompt appears with the new card name on the list of items.
WARNING:
ENSURE THAT YOU ENTER A NEW CARD NAME. IF
AN EXISTING CARD NAME IS ENTERED, THE
TERMINAL WILL NOT CREATE A NEW CARD. ANY
CHANGES YOU MAKE WILL AFFECT THE EXISTING
CARD’S PARAMETERS.
6. Select the list item with the new card name on it. The
Third Party Card Setup
menu appears with the card name displayed.
7. Select
Host Number
. The
Enter Host Number
prompt appears with ten
options. Host Numbers that have not been set up are unavailable and are
greyed out on the menu. Host 0 is the Moneris Host.
8. Select the host number list item that corresponds to the Third Party Host you
will use for processing this Third Party Card. The Third Party Host must be
set up already. The
Third Party Card Setup
menu reappears.
9. Configure the BIN Ranges for each of the three bins. You should receive the
BIN Ranges from your Third Party Card provider.
a. Select
BIN Range #1-Low
. The
BIN Range #1-Low
prompt appears with a
numeric keypad.
b. Key in the low BIN Range value (min. 1, max. 10 digits) for this card and
press
Enter
. The
Third Party Card Setup
menu reappears.
c. Repeat steps 9a. and 9b. for
BIN Range 1-High
,
BIN Range 2-Low
and
-
High
and
BIN Range 3-Low
and
-High
.
10. Select
Perform MOD10 Check
. The
Perform MOD10 Check?
prompt
appears.
11. Select
Yes
to have a MOD10 check performed on the customer’s card OR
Select
No
to skip the MOD10 check.
The
Third Party Card Setup
menu reappears.
12. This step is optional. If the Third Party Host has the SNS format, you can
enable Draft Capture transactions.
a. Select
Draft Capture
. The
Draft Capture
prompt appears.
b. Select
Yes
to store Third Party Card transactions in the draft capture mem-
ory and print a receipt. The
Third Party Card Setup
menu reappears.
13. Press
Exit
to save the changes. The
Select Card Name or Press Enter for New
Card
prompt reappears.
14. Press
Exit
. The
Terminal Configuration
menu reappears.
The SmartSELECT is now able to process transactions for the Third Party Card.
Summary of Contents for smartselect
