SmartSELECT Merchant Operating Manual v 2.0
31
Configuring Your Terminal
4.6: Other Configuration Parameters
The following parameters are not configured during the Configuration Shortcut.
You must enable each of them individually if you wish to use them. They are
accessed via the
Terminal Configuration
Menu.
Note:
The
Swipe Admin Card
prompt may appear when you attempt to
change a parameter if your terminal:
- processes Debit Cards
OR
- processes only Credit Cards and requires extra security.
4.6.1: Screen Control
Use this function to adjust the screen contrast if the screen is too dark or too light
and recalibrate the touch screen.
Change Screen Contrast
From the Idle screen:
1. Press
Menu
. The
Financial Transactions
menu appears.
2. Press
Config
. The
Terminal Configuration
menu appears.
3. Scroll down and select
Screen Control
. The
Swipe Admin Card
prompt
appears.
4. Swipe the POS Admin Card. The
Screen Control
prompt appears.
5. Select
Contrast
. The
Contrast
prompt appears with 20 options, 1 representing
Low contrast and 20 representing High contrast. The current contrast level
appears in white text on a black item.
6. Select the contrast level list item that represents the contrast level you want on
the touch screen and press
Enter
. The terminal displays
Please Wait
while the
new setting is saved.
7. When the setting is saved the
Screen Control
prompt reappears.
8. Press
Exit
to return to the
Terminal Configuration
menu.
Change Screen Alignment
From the Idle screen:
1. Press
Menu
. The
Financial Transactions
menu appears.
2. Press
Config
. The
Terminal Configuration
menu appears.
3. Scroll down and select
Screen Control
. The
Swipe Admin Card
prompt
appears.
4. Swipe the POS Admin Card. The
Screen Control
prompt appears.
5. Select
Alignment
. The Touchscreen Calibration process prompts you to
Touch Point #_
on the screen.
6. Touch each square on the screen as accurately as possible in the order they
appear. When you have touched all four points, the terminal displays
Please
Wait
while the new setting is saved.
7. When the Calibration is setting is saved, the terminal displays either
Calibra-
tion Successful
or
Calibration Failed
for three seconds then the
Screen Control
prompt reappears.
Summary of Contents for smartselect
