Monessen Hearth DELUXE RADIANT WOOD BURNING FIREPLACE SWB400I Installation & Operation Manual Download

Page: 27 / 40

FINISHED WALL

FRAMING

1/4"

INSTALLATION OF NONCOMBUSTIBLE TRIM MATERIALS TO THE FRONT FACE OF THE FIREPLACE

COMBUSTIBLE FRAMING

COMBUSTIBLE FRAMING
MEMBERS FACING MATERIAL

MEMBERS FACING MATERIAL
TO TOP OF SPACERS.

TO TOP OF SPACERS.

CAUTION: DO NOT COVER

CAUTION: DO NOT COVER
OR RESTRICT VENT AREAS

OR RESTRICT VENT AREAS
WITH ANY TRIM MATERIALS.

WITH ANY TRIM MATERIALS.

USE ONLY NONCOMBUSTIBLE

USE ONLY NONCOMBUSTIBLE
MATERIALS BELOW TOP OF SPACERS.

MATERIALS BELOW TOP OF SPACERS.

NONCOMBUSTIBLE

FACING MATERIAL

CAUTION: DO NOT ALLOW ANY TRIM MATERIALS TO EXTEND CLOSER THAN 3/8-INCH TO THE

CAUTION: DO NOT ALLOW ANY TRIM MATERIALS TO EXTEND CLOSER THAN 3/8-INCH TO THE
VERTICAL EDGES OF THE FIREBOX OPENING IF GLASS DOORS ARE TO BE INSTALLED.

VERTICAL EDGES OF THE FIREBOX OPENING IF GLASS DOORS ARE TO BE INSTALLED.

FIREPLACE FACE

STEEL LINTEL

STEEL LINTEL
(OPTIONAL)

(OPTIONAL)

WARNING: THE SPACE BETWEEN

WARNING: THE SPACE BETWEEN
THE FACE OF THE FIREPLACE

THE FACE OF THE FIREPLACE
AND THE NONCOMBUSTIBLE

AND THE NONCOMBUSTIBLE
FACING MATERIAL MUST BE

FACING MATERIAL MUST BE
SEALED. FAILURE TO PROPERLY

SEALED. FAILURE TO PROPERLY
SEAL THIS CRACK CAN CAUSE A

SEAL THIS CRACK CAN CAUSE A
POSSIBLE FIRE HAZARD AND WILL

POSSIBLE FIRE HAZARD AND WILL
VOID THE MARTIN WARRANTY.

VOID THE MARTIN WARRANTY.

SCREENED OPENING

OF FIREPLACE

(REF.)

EXTEND LINE FROM OPPOSITE REAR OF

EXTEND LINE FROM OPPOSITE REAR OF
FIREBOX THRU A POINT 4" IN FRONT OF

FIREBOX THRU A POINT 4" IN FRONT OF
FIREPLACE FACE, AND 1" OUTSIDE OF

FIREPLACE FACE, AND 1" OUTSIDE OF
SCREENED OPENING.

SCREENED OPENING.

OUTLINE OF

OUTLINE OF
FIREPLACE

FIREPLACE
FIREBRICK

FIREBRICK

COMBUSTIBLE TRIM

COMBUSTIBLE TRIM
MATERIALS MAY BE PLACED

MATERIALS MAY BE PLACED
WITHIN SHADED AREAS.

WITHIN SHADED AREAS.
(NOTE: COMBUSTIBLE

(NOTE: COMBUSTIBLE
MATERIALS MUST NOT

MATERIALS MUST NOT
OVERLAP BLACK PAINTED

OVERLAP BLACK PAINTED
SURFACE OF FIREPLACE.)

SURFACE OF FIREPLACE.)

IT IS RECOMMENDED THAT YOU

IT IS RECOMMENDED THAT YOU
INSULATE OUTER AND INNER WALLS

INSULATE OUTER AND INNER WALLS
OF CHASE. ALWAYS MAINTAIN THE

OF CHASE. ALWAYS MAINTAIN THE
PROPER CLEARANCE.

PROPER CLEARANCE.

1" AIR SPACE TO SIDES

1" AIR SPACE TO SIDES
AND REAR OF FIREBOX

AND REAR OF FIREBOX

USE ONLY NONCOMBUSTIBLE

USE ONLY NONCOMBUSTIBLE
MATERIALS BELOW TOP

MATERIALS BELOW TOP
OF SPACERS.

OF SPACERS.

OUTSIDE AIR INLET

SAFETY STRIP

HEARTH EXTENSION

TOP EDGE OF FIREPLACE OPENING

TOP EDGE OF FIREPLACE

INSTALLATION OF COMBUSTIBLE MANTEL

INSTALLATION OF COMBUSTIBLE TRIM ALONG SIDES OF FIREPLACE

COMBUSTIBLE FRAMING MEMBERS

COMBUSTIBLE FRAMING MEMBERS
FACING MATERIAL TO TOP OF SPACERS.

FACING MATERIAL TO TOP OF SPACERS.

COMBUSTIBLE MANTEL

12" MAXIMUM

18"

MINIMUM FROM FIREPLACE OPENING TO

BOTTOM OF A COMBUSTIBLE MANTEL, AS

BOTTOM OF A COMBUSTIBLE MANTEL, AS
RECOMMENDED BY FIREPLACE MANUFACTURER.

RECOMMENDED BY FIREPLACE MANUFACTURER.
(SEE NOTE BELOW REGARDING

(SEE NOTE BELOW REGARDING

H36

HOOD.)

NOTE: IF AN APPROVED ANSI Z21.11.2 UNVENTED ROOM HEATER IS TO BE INSTALLED IN T

NOTE: IF AN APPROVED ANSI Z21.11.2 UNVENTED ROOM HEATER IS TO BE INSTALLED IN THIS FIREPLACE IN A RESIDENTIAL TYPE

HIS FIREPLACE IN A RESIDENTIAL TYPE

HOME, A MARTIN

H36

HOOD MAY ALSO BE INSTALLED ON THE FIREPLACE TO REDUCE THE

18"

RECOMMENDED CLEARANCE FROM

THE TOP EDGE OF THE FIREPLACE OPENING TO THE BOTTOM OF A COMBUSTIBLE MANTEL TO

12"

INSTEAD OF THE SPECIFIED

18"

NOTICE:

ANY GLASS DOORS ON THE FIREPLACE HAVE TO BE PERMANENTLY REMOVED IN ORDER TO UTIL

ANY GLASS DOORS ON THE FIREPLACE HAVE TO BE PERMANENTLY REMOVED IN ORDER TO UTILIZE THE

IZE THE

H36

HOOD.

WARNING:

THE

H36

HOOD CAN NOT BE INSTALLED ON A FIREPLACE WHICH IS INSTALLED IN A MANUFACTURED HO

HOOD CAN NOT BE INSTALLED ON A FIREPLACE WHICH IS INSTALLED IN A MANUFACTURED HOME BECAUSE

ME BECAUSE

GLASS DOORS ARE MANDATORY ON FIREPLACES INSTALLED IN MANUFACTURED HOMES.

RIM

NSTALLATION

IGURE

WARRANTY.

53D9033. Rev 1 03/03

Summary of Contents for DELUXE RADIANT WOOD BURNING FIREPLACE SWB400I









































Search results

Summary of Contents for DELUXE RADIANT WOOD BURNING FIREPLACE SWB400I

Reviews:

Related manuals for DELUXE RADIANT WOOD BURNING FIREPLACE SWB400I

Brands by name

Popular brands

Monessen Hearth DELUXE RADIANT WOOD BURNING FIREPLACE SWB400I, Installation & Operation Manual

Search results

Summary of Contents for DELUXE RADIANT WOOD BURNING FIREPLACE SWB400I

Reviews:

Related manuals for DELUXE RADIANT WOOD BURNING FIREPLACE SWB400I

Brands by name

Popular brands