background image

2

424WBST Designer Woodburning Fireplaces

87D1506

Safety Information

PLeASe ReAD THIS MANUAL BeFORe INSTALLINg AND USINg FIRePLACe.
IMPORTANT: 

Read all instructions and warnings carefully before starting installation.  Failure to 

follow these instructions may result in a possible fire hazard and will void the warranty.

Description

The 424WBST fireplaces are multi-side solid fuel, wood-
burning fireplaces. These are radiant models only and 
include a preinstalled outside air kit.

Precautions

Monessen Fireplaces and component parts have been 
highly tested and will operate safely when installed in 
accordance with instructions provided in this manual. 
Carefully read and understand all instructions 

before

 

beginning installation.
If you notice any damage to fireplace or component parts, 
immediately report damage to your Monessen Fireplaces 
dealer.
Only use MHSC components or the warranty will be 
voided and a fire hazard may be created.
MHSC warranty will be voided by and MHSC

 

disclaims 

any responsibility for the following actions:

• 

Installation by any other than a qualified install-
er, preferably NFI or WeTT (Canada) certified.

• 

Installation of any damaged fireplace or chim-
ney component;

• 

Modification of fireplace, chimney assembly or 
any component parts thereof; (except for chase 
flashings as detailed in the Chimney Top instal-
lation instructions).

• 

Installation other than as instructed by MHSC; 
or

• 

Installation and/or use of any component part 
not manufactured or approved by MHSC in 
combination or assembly with a Monessen Fire-
places fireplace system, notwithstanding any 
independent testing laboratory or other third 
party approval of such component parts or ac-
cessory.

Any such action may possibly cause a fire hazard.

Consult local building codes to ensure that you are in 
compliance 

before 

installing the fireplace.

Fireplaces must be vented to the out-of-doors.

Do not obstruct or modify air inlets/outlets in any 
manner. 

Do not install combustible materials on any of the 
black fireplace surround.
Burn only solid wood fuel or gas logs.
Do not install a solid fuel burning insert or other 
products not specified for use with this fireplace.

Proposition 65 Warning: 

Fuels used in gas, wood-

burning or oil fired appliances, and the products of 
combustion of such fuels, contain chemicals known to 
the State of California to cause cancer, birth defects 
and other reproductive harm.
California Health & Safety Code Sec. 25249.6

WARNINg: Check with your electronics manufacturer 
before installing a television or other electronic de-
vice above this fireplace.

Drafts

The fireplace should not be located in areas that create 
drafts (ie: frequently opened doors and central heating air 
inlets/outlets) that hamper the normal flow of air into the 
fire.

gas Logs

If you plan to install a gas log, the gas line should be 
installed 

before

 framing the fireplace. The gas line must 

be installed by a certified gas line installer.

424WBST

Listed

UL 127 / ULC-S610

Standard for Factory Built Fireplaces

Safety Information . . . . . . . . . . . . . . . . . . 2
Specifications and Framing   . . . . . . . . . . 3
Parts Identification  . . . . . . . . . . . . . . . . . 4
Chimney Requirements  . . . . . . . . . . . . . 6
Planning Information . . . . . . . . . . . . . . . . 7
Installation   . . . . . . . . . . . . . . . . . . . . . . . 8
Replacement Parts . . . . . . . . . . . . . . . . 20
Accessories   . . . . . . . . . . . . . . . . . . . . . 22

Table of Contents

Summary of Contents for WOODBURNING FIREPLACE 424WBST

























Reviews: