background image

LIMITeD WARRANTY

Factory-Build Fireplace and Components

(except Blowers)

What is Covered and For How Long

Five-Year Coverage:

 For five years from the date this fireplace and components are first purchased for use, MHSC 

will, at its option, repair or replace any defective part of this fireplace or components, or refund to you a sum not to 
exceed the factory retail price in effect at the time of purchase.

Ten-Year Coverage:

 From the sixth through the tenth year following the date this fireplace or accessory is first 

purchased for use, MHSC will make available to you, at our factory, a free replacement for any defective part in this 
fireplace or accessory.

Twenty-Five-Year Availability of Replacement Parts:

 From the eleventh through the twenty-fifth year following the 

date this fireplace or accessory is first purchased for use, MHSC will make available at our factory replacement parts 
for this fireplace or accessory, which you may purchase for the list price current at the time your purchase order is 
received.

What is Not Covered

•  This limited warranty does not cover:
•  Transportation or shipping cost.
•  The cost of a service call to diagnose trouble.
•  Painted surfaces.
•  Damage or defect caused by improper installation, accident, misuse, abuse or alteration.
•  Poor ventilation of smoke or gases caused by air-conditioning and heating systems, exhaust fans, or pressure dif-

ferentials produced by wind.

•  Broken glass components.
•  Cracks in ceramic and castable parts that do not affect safe operation.
•  We do not warrant this fireplace to be in compliance with your local building code. Building codes vary greatly 

throughout the country, and you should determine whether your local building code contains restrictions on the use 
of this fireplace before you purchase it.

•  Blowers or fans, which are warranted separately.
•  Heat loss due to the passage of heat or air through or around the fireplace.
Also, under our five year coverage, we do not pay the cost of removal and replacement of any portion of the structure 
in which the fireplace is situated, made necessary by the repair, removal or re-installation of the fireplace.
And under our twenty-five year warranty of availability of replacement parts, we only promise to maintain a supply of 
replacement parts at our factory for you to purchase.

Limitations and exclusions

1.  No one has authority to add to or vary this limited warranty, or to create for MHSC any other obligations of liability 

in connection with this fireplace and accessory.

2.  MHSC shall not be liable for incidental, consequential, special or contingent damages you might suffer as a result 

of its breach of this written warranty or any implied warranty. Some states do not allow the exclusion of limitation of 
incidental or consequential damages, so the above limitations may not apply to you.

3.  This warranty applies only to a fireplace sold and used in the United States.

IF WARRANTY SeRVICe IS NeeDeD...

1.  Contact your supplier. Make sure you have your warranty, your sales receipt and the model/serial number of your 

MHSC product.

2.  DO NOT ATTEMPT TO DO ANY SERVICE WORK YOURSELF.

MHSC

149 Cleveland Drive • Paris, Kentucky 40361

www.mhsc.com

Summary of Contents for WOODBURNING FIREPLACE 424WBST

























Reviews: