background image

10

CONTROL

STRATEGY

Table 1 - Damper and Louvre Operational Strategy

Season

Spring

Summer

Autumn

Winter

Start Date

01 March

01 June

01 September

01 December

Finish Date

31 May

30 August

30 November

Last Day of Feb

Zone Temperature

Damper Output

Up to 16°C

Dampers Closed

Dampers Closed

Dampers Closed

Dampers Closed

At 17°C

Dampers Open 20%

At 18°C

Dampers Open 40%

At 19°C

Dampers Open 60%

At 20°C

Dampers Open 20% Dampers Open 80% Dampers Open 20%

At 21°C

Dampers Open 40%

Dampers Fully 

Open

Dampers Open 40%

At 22°C

Dampers Open 60%

Dampers Open 60% Dampers Open 10%

At 23°C

Dampers Open 80%

Dampers Open 80% Dampers Open 20%

At 24°C

Dampers Fully 

Open

Dampers Fully 

Open

Dampers Open 30%

At 25°C

Dampers Open 40%

At 26°C

Dampers Open 50%

Night-time Cooling

X

X

X

ActivLouvre Opening

50%

100%

50%

25%

The iNVent 2 panel uses a Seasonal Automatic Temperature Control strategy to 

manage the air quality and room temperature of a zone. It varies the damper 

and louvre openings of Monodraught Natural Ventilation systems based on 

the internal and external temperatures, and adjusts for the current season.

The external temperature is also used to activate Frost Mode. This mode 

closes the louvres if the external temperature is below 5°C in order to ensure 

that the louvres do not freeze open. If the external temperature is less than 

8°C and the rain sensor activates, then the system enters Snow Mode and 

closes the louvres.

During hotter weather, if required, dampers can be set to close when the 

internal temperature is at least 25°C and the external temperature is at least 

5°C above the internal temperature. This feature is designed to prevent 

a space from heating up due to higher outside air temperatures (i.e. 30°C 

outside, 25°C inside).

In addition to the above control strategy the system will cycle the Active Louvre 

fully each day at 2.00 am to ensure there is no dirt build up that may inhibit the 

movement brought on by a long period of the louvres not actuating fully. 

Further to the seasonal position of the louvres the over-ride open facility no 

longer fully opens the louvres fully every time but will move the louvres to 

the position of the next season as indicated in Table 3 below.

The iNVent 2 control system will adjust the active seasonal strategy depending 

upon the external temperature based on the following table:

Table 2 - Seasonal Strategy Based on Noon External Temperatures

Current Calendar Season

Spring

Summer

Autumn

Winter

External Temperature (ET)

Operational Season for next 24 Hours

ET < 8°C

Winter

Spring

Winter

Winter

8°C < ET < 15°C

Spring 

Spring

Autumn

Winter

15°C < ET < 22°C

Spring

Summer

Autumn

Spring

ET > 22°C

Summer

Summer

Summer

Spring

Table 3 - Louvre Override Open Position vs. Season

Current Calendar Season

Spring

Summer

Autumn

Winter

Override Open Position

100%

100%

100%

50%

CO2 Control (requires controller within the zone to have 

integrated CO2 sensor)

If the CO

2

 Level in the zone exceeds 1500 ppm the system will open the 

dampers 20% further than the current setting if they are currently open 20% 

to 80% otherwise they open to 20%.
If after 5 minutes the CO

2

 level is still > 1300 ppm the dampers will open a 

Summary of Contents for INVENT 2













Reviews: