background image

Installation Instructions

12

STEP 10A  WATER LINE 

INSTALLATION WITH 

A REVERSE OSMOSIS

SYSTEM 

Skip this step when not using RO System.

If the water supply to the refrigerator is from a Reverse
Osmosis Water System, use the refrigerator’s filter
bypass plug. 

You must also use the filter bypass plug when 
a replacement filter cartridge is not available. 
The icemaker will not operate without the filter 
or filter bypass plug.

Replacement Filters:

To order additional filter cartridges in the United
States, visit our Website, ge.com, or call GE Parts 
and Accessories, 800.626.2002.

Filter Model GSWF

Customers in Canada should consult the yellow pages 
for the nearest Mabe Service Center.

STEP 11  CONNECT WATER SUPPLY

Check to be sure that refrigerator power cord is not
plugged into the wall outlet.

If you are using copper tubing:

• Place compression nut and ferrule (sleeve) onto 

the end of the tubing coming from the house water
supply.

• Insert the end of the copper tubing into 

the refrigerator connection at the back 
of the refrigerator, as far as pos si ble. 
Hold the tubing in place and tighten the fitting.

If you are using GE SmartConnect

tubing:

• Insert the molded end of the tubing into 

the refrigerator connection, at the back of 
the refrigerator, and tighten the compression 
nut until it is hand tight.

• Then tighten one additional turn with a wrench.

Overtightening may cause leaks.

• Fasten the tubing into the clamp provided to hold it 

in position. You may need to pry open the clamp.

• Turn on the water at the shut-off valve to check 

for leaks.

STEP 12  CONNECT POWER

• Connect refrigerator power cord plug to a properly

ground ed receptacle. 

• Check to make sure power to refrigerator is on by

opening refrigerator door to see if interior lights 
are on.

1/4"

Tubi

ng

Tubi

ng 

Cl

am p

1/4"
Com pressi

on 

Nut

Ferrul

(sl

eeve)

SmartConnect™ 

T

ubing

Refri

gerator 

Connecti

on

STEP 13  MOVE REFRIGERATOR

INTO POSITION

• Remove outside protective wrapping.
• Move the refrigerator into final in stal la tion position.
• Remove door spacer, if not removed earlier, 

and all inside packaging.

Summary of Contents for WX08X10002

















Reviews: