21
31-1000600 Rev. 0
Installation Instructions - Dual Integrated Installation
STEP 4 INSTALL ANTI-TIP BRACKET
(Cont.)
Ŷ
Measure and mark from the RH side of the opening
per the table above depending on the size of the RH
unit you are installing.
Ŷ
Measure and mark again from the RH side of
the opening per the table and depending on your
combination of LH and RH units.
For example, if installing an 18” LH unit and a 30” RH
unit, use 5-3/4” and 38-5/8”.
Ŷ
Mount the anti-tip bracket centered about the marks
and flush to the floor as shown. Mark 3 holes for wall
mounting or 4 holes for floor mounting.
WOOD MOUNTING:
Predrill with 3/16” drill bit, 2”
deep, then install lag bolts with a 7/16” driver.
CONCRETE MOUNTING:
Predrill with a 5/32”
concrete bit, 2” deep, then install
tapcon screws with a 7/16” driver.
STEEL MOUNTING:
Predrill with a
1/2” drill bit, insert toggle, then install
bolts with a 7/16” driver.
The bracket must be screwed to
either the FLOOR or REAR WALL.
Ŷ
If the enclosure is deeper than 25 ½”, the anti-tip
bracket should be secured to the floor 25” from front
of the enclosure.
Ŷ
Tape the waterline to the wall and floor per
dimensions shown. Apply tape about every 5” toward
front of unit. This will keep the waterline away from
the anti-tip bracket(s) and prevent the unit from
rolling over the waterline during installation. Do not
tape near the cabinet front in order to keep tape
hidden under the unit.
WARNING
Tip Over Hazard.
These appliances are top heavy, especially with any
doors open, and must be secured to prevent tipping
forward which could result in death or serious injury.
Read and follow the entire installation instructions
for securing the appliance with the anti-tip system.
5"
36"
18"
24"
30"
36"
24"
30"
36"
36"
18"
5"
10" (24", 30", 36" units)
5" (18" unit)
10" (24", 30", 36" units)
12" (18" unit)
STEP 4 INSTALL ANTI-TIP BRACKET
Ŷ
Remove the anti-tip bracket from the hardware kit.
Ŷ
Anti-tip bracket should be mounted against the back
wall or up to 25-1/2” (64.7 cm) maximum from front of
opening. Use floor mounting method if the bracket is
not against a wall (bracket hardware is provided for
mounting into wood, steel studs and concrete).
Ŷ
Two Anti-tip brackets are used for each 36” product.
AVERTISSEMENT
Risque de
basculement.
Ces électroménagers sont lourds du
haut, notamment lorsqu’une porte est ouverte, de sorte
qu’ils doivent être fixés pour prévenir un basculement
vers l’avant susceptible d’occasionner des blessures
graves ou la mort. Lisez et observez la totalité des
instructions d’installation pour connaître la façon de fixer
l’électroménager sur le dispositif antibasculement.
ADVERTENCIA
Riesgo de Caídas
Estos electrodomésticos son inestables, especialmente
cuando una puerta se encuentre abierta, y deben estar ase-
gurados a fin de evitar caídas hacia adelante que podrían
resultar en la muerte o en lesiones graves. Lea y siga las
instrucciones de instalación en su totalidad para asegurar el
electrodoméstico con el sistema anti volcaduras.
Dual install
LH unit
RH unit
18
24
30
36
26-5/8”
67.6 cm
23-1/2”
59.7 cm
23-1/2”
59.7 cm
23-3/4”
60.3 cm
8-7/8”
22.5 cm
18
32-5/8”
82.9 cm
29-1/2”
74.9 cm
29-1/2”
74.9 cm
29-3/4”
75.6 cm
5-3/4”
14.6 cm
24
38-5/8”
98.1 cm
35-1/2”
90.2 cm
35-1/2”
90.2 cm
35-3/4”
90.8 cm
5-3/4”
14.6 cm
30
44-1/2”
113.0 cm
41-3/8”
105.1 cm
41-3/8”
105.1 cm
41-1/2”
(105.4 cm)
&
65-1/2”
(166.4)
6 “
(15.2 cm)
&
29-3/4”
(75.6 cm)
36
LH Unit
RH Unit
2 required for 36"
2 required for 36"
