background image

2

Safety Information

BEFORE YOU BEGIN

 

Read these instructions completely and carefully.

• 

IMPORTANT

 – 

Save these instructions for 

local inspector’s use. Observe all governing codes and 
ordinances.

• 

Note to Installer

 –

 Be sure to leave these 

instructions with the Consumer.

• 

Note to Consumer 

 –

 Keep these instructions with 

your Owner’s Manual for future reference.

If you received a damaged unit, you should immediately 
contact your dealer or builder.

Skill Level –

 Installation of this unit requires basic 

mechanical, carpentry and plumbing skills. Proper 
installation is the responsibility of the installer. Product 
failure due to improper installation is not covered under 
the GE Appliance Warranty. See the Owner’s Manual for 
warranty information.

For Monogram local service in your area, call 1.800.432-2737.
For Monogram service in Canada, call 1.800.561.3344
For Monogram Parts and Accessories, call 1.877.959.8688.

www.monogram.com

WARNING

  Electrical Shock Hazard.  

Plug into a grounded 3-prong outlet.

Do not remove the ground prong.

Do not use an adapter.

Immediately replace electric cords that become 
frayed or damaged.

Do not use an extension cord with this appliance.

Failure to follow these instructions can result in 
death, fire, or electrical shock.

Follow the instructions in the section 

Grounding the 

Unit

.

WARNING

 

 Tip Over Hazard.  

These appliances are top heavy, especially with any doors open, and must be secured to prevent tipping 
forward which could result in death or serious injury. Read and follow the entire installation instructions for 
securing the appliance with the anti-tip system.

WARNING

 

 Explosion Hazard.  

Keep flammable materials and vapors, such as gasoline, away from appliance.  Failure to do so can result 
in fire, explosion, or death.

WARNING

 

To reduce the risk associated with choking, do not allow children under 3 years of age to 

have access to small parts during the installation of this product.  

CAUTION

  Lifting Hazard 

This unit is very heavy. To reduce the risk of person injury during maneuvering and installing this appliance, 
3 people are required for proper installation.

Summary of Contents for ZIRP360NHLH





















































Reviews: