background image

 STEP 10   CONNECT WATER SUPPLY 

(FREEZER MODELS ONLY)

• Locate and bring the tubing to the front of the cabinet.
• Turn the water on to flush debris from the line. Run 

about a quart of water through the tubing into a 
bucket, then shut off the water.

Copper Tubing:

• Slip a 1/4” nut and ferrule (provided) over both ends  

of the copper tubing. Insert the tube into the union  
fitting on the unit and tighten the nut to the union.

• Turn on the water to check for leaks.

SmartConnect

 Tubing:

NOTE:

 The only GE Appliances-approved plastic tubing 

is supplied in the SmartConnect

 Refrigerator Tubing 

kits. Do not use any other plastic water supply line 
because the line is under pressure at all times. Other 
types of plastic may crack or rupture with age and 

cause water damage to your home.

• Insert the molded end of the tubing into the appliance 

or freezer connection. Tighten the compression nut 
until it is just hand-tight.

• Tighten one additional turn with a wrench. 

Overtightening can cause leaks!

• Turn on the water to check for leaks.

NOTE: 

Make sure excess tubing length does not 

interfere with the toekick installation.

Freezer

Water Supply

House

Water Supply

Installation Instructions - Standard Installation

21

 STEP 11  START ICEMAKER 
                (FREEZER MODELS 
ONLY)

• Slide the switch to ON. The icemaker will begin 

operation automatically.

• Be sure nothing interferes with the sweep of the 

feeler arm. 

• Discard the first full bucket of ice cubes.
• To turn the icemaker off, slide the switch to OFF.

Icemaker

Feeler Arm

Power 
Switch

 STEP 12  INSTALL TOEKICK

• Locate Supplied toekicks (shipped taped to the side 

of the appliance). The unit will be shipped with two 
sets of toekicks.  The shorter toe kick should be 
used for standard installation.  Discard the other set 
of toe kicks. Install the toekick assembly with the 2 
screws provided, adjust to the desired height and 
tighten the screws.

IMPORTANT: 

A custom toekick can be installed to 

match or complement the surrounding cabinetry but 
can NOT cover the horizontal vent slots of the factory 
toe kick. 

Summary of Contents for ZIRP360NHLH





















































Reviews: