1. Description of components
MT 88
2. Recommended spine width
1. The MT 88 thermal binder has a maximum binding capacity of 200 sheets.
2. The general guideline for selecting the thermal binding cover is as follows:
1 Put the machine on a flat table, then draw out the plastic panel on the back cover of
the machine.
2 Plug the machine in a standard socket, then turn on the ON/OFF switch
.
The red POWER light
will light up, the FINISHED light
will turn yellow, the machine
will then start to heat up.
3 After approximately 2 minutes, the green READY light
comes on and the FINISHED
light
will change from yellow to green, then it will give a short beep (not long beep),
the machine can now be used.
4 Put the paper into the file, ensuring the edge of the paper is close to the heating glue.
5 Move the retaining bracket
upwards Fig. 1.
6 Put the file (spine side) into the binding slot
Fig. 2 and let the plate clamp the file tightly.
7 Push the PUSH button
, the FINISHED light
will change to yellow and then about 50
seconds later, all the glue will melt in the file. The FINISHED light
will then change
to green, the binding will be finished with a short beep.
8 Pull the file out of the machine, and put it on the plastic panel
for cooling Fig. 3 and 4.
9 Press the Push
button to proceed with the next binding operation. If the object is not
bound well, please repeat the above procedure.
3. How to use
4. Safety advice and maintenance
Dear customer,
Congratulations! You have made an excellent choice with the purchase of this quality product. Our commit-
ment to quality also includes our service. Should you, contrary to expectations, experience defects due to
manufacturing faults during private use within 36 months of the date of purchase we shall be liable for
warranty in accordance with statutory warranty regulations provided that:
- the device was not put to any use other than the intended
- was not overloaded
- was not used with the wrong accessories
- repairs were not carried out by any other than the authorized workshop
The warranty certificate is only valid in connection with the receipt. Please keep both in a safe place.
This warranty does not affect your statutory rights.
This purchase is guaranteed for a period of three years beginning on the day of purchase. Keep your purchase
receipt safe as proof of date of purchase. The guarantee can only be extended for the duration of any repair
required.
During the warranty period if the product becomes defective, in the first instance, please call our service hot-
line. We will, at our discretion, either repair or exchange the device in accordance with warranty legislation.
If you are required to return the item please enclose the following:
1. Receipt (proof or purchase)
2. This warranty certificate with the fault report form overleaf complete with your name, contact details and
fault description.
If the original receipt is not enclosed the repair will be charged in all cases. After the warranty has expired you
can still send defective devices for repairs period to the address stated below. Quotes as well as repairs after
the warranty period are to be paid for in all cases.
Ensure that the product is sent well packed as no responsibility can be accepted for items lost or damaged in
transit.
This warranty does not affect your statutory rights.
Our monolith products undergo strict quality controls. If this equipment does not function perfectly,
please contact our
Service Hotline: 0 808 / 1 01 22 42 (UK), 1 800 / 65 50 09 (IR)
Our service hours are: Mon.-Thur. 08:00-17:00 and Fri. 08:00-15:00
We hope you have lots of fun with your new Thermal Binder!
IMPORTANT WARRANTY DOCUMENT – KEEP SAFE!
Warranty Card –
Thermal Binder
Guarantee Terms
Thermal binder
MT88/12 /08
monolith GmbH • Schwarze Horn 1 • D-45127 Essen
When using this electrical machine, basic precautions should always be followed to reduce the
risk of electric shock and injury to persons, including the following:
1 Read carefully the instruction on” HOW TO USE”.
2 Whilst using the machine, please do not put any items on the upper cover.
Please do not touch any heating areas, with your hand or any objects as there is
a danger of burning or fire.
4 Always unplug the machine when not in use or before cleaning.
5 Please only plug in sole socket for safety.
6 Keep away from children and pets whilst in operation.
7 To protect against risk of electrical hazards, do not immerse cord, plug, or machine in water
or other liquid.
8 Do not operate the machine with a damaged cord or plug, or after the machine
malfunctions, has been dropped or is damaged in any manner. Return machine to the
nearest authorised service centre for examination, repair or adjustment.
9 Do not use accessory attachment not recommended or sold by the machine manufacturer.
10 Do not let the cord hang over edge of counter, or touch hot surface.
11 The socket-outlet shall be installed near the equipment and shall be easily accessible.
Meaning of the warning symbols
Caution!
Read the instructions!
The best way to store the machine when not in use is in the original packaging. Keep
the machine in a dry location away from sources of heat.
6. Disposal
The product packaging is recyclable and should be disposed of with due regard for the
environment. When no longer serviceable, the machine should not be thrown away
with the household rubbish, but should be disposed of in line with legal requirements.
This is in the interests of recycling and protecting the environment. Discuss the options
with your local authority. Before disposal ensure that the machine is rendered unusable.
Disconnect the machine from the power supply and remove the mains cable.
5. Storage
Cover spine
width in mm
Max. number of
80 g/m
2
sheets
1
10
2
20
3
30
etc.
è
Fig. 1
Fig. 3
Fig. 2
Fig. 4
è
5
4
2
3
1
6
7
8
1
ON/OFF switch
“Power” light
3
“Ready” light
4
“Finished” light
5
Push button
6
Binding slot
7
Cooling stand
Retaining bracket
2
8
Helpline No.: 0 808 / 1 01 22 42 (UK), 1 800 / 65 50 09 (IR) • Model Number: MT 88
monolith GmbH • Schwarze Horn 1 • D-45127 Essen • www.monolithshop.de
Helpline No.: 0 808 / 1 01 22 42 (UK), 1 800 / 65 50 09 (IR) • Model Number: MT 88
monolith GmbH • Schwarze Horn 1 • D-45127 Essen • www.monolithshop.de
3
Helpline No.: 0 808 / 1 01 22 42 (UK), 1 800 / 65 50 09 (IR) • Model Number: MT 88
monolith GmbH • Schwarze Horn 1 • D-45127 Essen • www.monolithshop.de
4
Helpline No.: 0 808 / 1 01 22 42 (UK), 1 800 / 65 50 09 (IR) • Model Number: MT 88
monolith GmbH • Schwarze Horn 1 • D-45127 Essen • www.monolithshop.de
5
