background image

INTRODUCTION 

Thank you for purchasing this Blackbird™ 4x4 HDMI® Matrix/Extender! This matrix/extender 
allows you to connect up to four HDMI video source devices and distribute them to four 
local HDMI displays and four remote displays at the same time. It can extend 1080p@60Hz 
video signals to distances up to 164 feet (50 meters) over a single Cat6 Ethernet cable. It 
supports the Power over Cable (PoC) feature, allowing the remote receivers to receive 
their power over the Ethernet cable. It can be controlled using the front panel buttons, the 
included IR remote control, an internet browser using the TCP/IP control option, or a 
computer using the RS232 control option. It supports IR extension so you can control the 
source devices from the remote locations. 
 

FEATURES 

 

Distributes any of four HDMI® source devices to any of four pairs of outputs 

 

Simultaneously supports local displays and displays connected to remote receivers 

 

Supports video resolutions up to 1080p@60Hz 

 

Can extend 1080p video signals to distances up to 164 feet (50 meters) over a single 
Cat6 Ethernet cable 

 

Supports wide band IR extension for control of source devices from the remote 
locations or the remote displays from the source location 

 

Delivers up to 4.95 Mbps bandwidth 

 

Includes smart EDID management 

 

Fully compliant with the HDMI 1.3, HDCP 1.1, and DVI 1.0 standards 

 

Can be controlled using the front panel controls, the included IR remote control, an 
internet browser using the TCP/IP control option, or a computer using the RS232 
control option 

 

 

Summary of Contents for 21905















Reviews: