background image

NOTE: For use as a stand alone blacklight always on (without DMX)
set Brightness to P255 and Strobe to FS00

1. Press the 

MENU

 button to turn on the menu display.

2. Press the 

UP

 or 

DOWN

 buttons until 

CoLo

 is displayed.

3. Press 

ENTER

 repeatedly until 

Pxxx

 is

displayed (xxx can be any number).

4. Use the 

UP

 and 

DOWN

 buttons to set the

brightness level of the light.

5. Press 

ENTER

 until 

SPxx

 is displayed (xx

can be any number).

6. Use the 

UP

 and 

DOWN

 buttons to set the

speed of the strobing effect, from 0 (no
strobing) to 20 (20Hz).

Slave Mode 

Only one fixture in each DMX chain can be the Master. All others must be set to Slave. 

1. Press the 

MENU

 button to turn on the menu display.

2. Press the 

UP

 or 

DOWN

 buttons until 

SLAu

 is displayed.

3. Press 

ENTER

 to select Slave mode. The display will

read 

SLa

.

MASTER/SLAVE MODE

Whenever the light is set to a mode other than a DMX address or Slave mode, it is 
considered to be in Master mode. For example, when set to the Sound Activated 
operation, it is in a Master mode. 

When the light is the Master, it will send DMX instructions to other connected lights. 
Those other lights must be set to Slave mode (SLAu) to receive and execute the 
instructions sent by the Master light. 

Note: Only one light in any DMX Universe can be the Master. All other lights in the chain 
must be set to Slave mode (SLAu). 

Strobe Mode

Summary of Contents for 612610











Reviews: