background image

© 2011 Monte Carlo Fan Company

4/20/2012

4

Insert downrod into motor yoke.

Next, insert clevis pin through yoke

and downrod and secure with cotter

pin. 

Carefully lift fan assembly onto

mounting bracket. Rotate fan so that

the notch on the ball engages the

ridge in the mounting bracket. This

will allow hands-free wiring. 

16

12

Install canopy and yoke cover over

the downrod. Thread wire through

downrod with canopy and yoke cover

assembled.

11

13

Tighten both yoke set screws to fur-

ther secure downrod. Reinstall the

downrod ball previously removed.

Loosen the 2 set screws. You should

be able to put your downrod into the

yoke.

10

Remove the shipping stabilizers

and discard.

15

17

Hang assembled fan from the mounting bracket

installed to ceiling in previous step.  Make sure

the fan is hanging straight.  Rotate fan until the

tab on the Mounting bracket engages the slot

on the Downrod Ball.  This must be done to

prevent the fan body from rotating when the

blades are in motion.

Re-install safety bar removed in step.

3  by placing safety bar on screws,

sliding into place, and tightening the

2 screws.

18

Install the two thumbscrews to

secure the yoke cover. Tighten

securely.

14

Summary of Contents for 5DCR60XX Series











Reviews: