background image

© 2013 Monte Carlo Fan Company

8/13/2013

3

Before you begin installing the fan, Switch

power off at Service panel and lock service dis-

connecting means to prevent power from being

switched on accidentally.  When the service dis-

connecting means cannot be locked, securely

fasten a prominent warning device, such as a

tag, to the service panel.

Before installing this fan make sure the outlet box is
properly installed to the house structure.  To reduce
the risk of fire, electric shock, or personal injury,
mount to outlet box or supporting system acceptable
for fan support. (Mounting must support at least 35
lbs.)

Use metal outlet box suitable for fan support
(must support 35 lbs). Before attaching fan to
outlet box, ensure the outlet box is securley
fastened by at least two points to a structural
ceiling member ( a loose box will cause the fan
to wabble).  

Use only the screws provided

with the outlet box.  

3

2

1

Loosen the 2 set screws till you can not

feel them on inside of yoke.  

Note

: If install fan on vaulted ceiling,

make sure open end of mounting

bracket is installed facing the higher

point of the ceiling and make sure the

ceiling angle is not steeper

than 30º.

4

yoke

Place downrod into fan yoke.

7

Install the keeper to pin.

9

Align the hole in the Downrod with the hole in
the Yoke. Insert the Pin through the Yoke and
Downrod until the point appears on the other
side.  

8

Downrod mount installation

Remove Keeper pin and cross pin

from downrod. Place canopy and

caonpy disk cover over downrod. 

Canopy

Tread leadwires and safety

cable through downrod. 

Downrod

6

5

Canopy 

disk

Cross

pin

Keeper

pin

Downrod

Summary of Contents for 5DI44









Reviews: