background image

Page 3

H52-DF Gas Fireplace

Part No. XG0650

Introduction

Thank You

 for choosing a Montigo Gas Fireplace.

About this Fireplace:

The 

H52-DFN 

is a fireplace with a pan-style burner and glowing embers. 

This fireplace is ONLY available as a Top Vent, natural gas fireplace.

The 

H52-DFN

 is rated for Natural Gas at 60,000 BTU/H (17.65 Kilowatts) 

Input. Available in

 

Intermittent Pilot (HSI), NG Models Top Vent Only.

How to use this manual:

This manual covers installation, operation and maintenance. Lighting, 

operation and care of this fireplace, and can be easily performed by 

the homeowner. However, all installation and service work should be 

performed by a qualified or licensed installer, plumber, or gas fitter who 

is qualified or licensed by the state, province, region, or governing body 

in which the appliance is being installed.

Warranty and Installation Information:

The Montigo warranty will be voided by, and Montigo

 

disclaims any 

responsibility for, the following actions:

Modification  of  the  fireplace  and/or  components  including  Direct-Vent 

 

assembly or glass doors.
Use of any component part not manufactured or approved by Montigo in 

 

combination with this Montigo fireplace system.

Installation other than as instructed in this manual.

 

Consult your local Gas Inspection Branch on installation requirements 

for factory-built gas fireplaces. Installation & repairs should be done by 

a qualified contractor.

Installations in Canada

 must conform to the current 

CAN/CGA B-

149.1

 and 

.2

 Gas Installation Code and local regulations. If the optional 

air-circulating fan kit is installed, it must be electrically grounded in 

accordance with 

CSA C22.1

 Canadian Electrical Code Part 1 and/or 

Local Codes.

Installations in the USA

 must conform to local codes, or in the absence 

of local codes to the National Fuel Gas Code, 

ANSI Z223.1-1988

. If the 

optional air-circulating fan is installed, it must be grounded in accordance 

with local codes or, in the absence of local codes, with the National 

Electrical Code, 

ANSI/NFPA 70-1987. See Appendix B 

for installation 

within the State of Massachusetts.

Important:  

Natural Gas equipped models may be installed using 

Top Vent applications ONLY.

     CAUTION!

Due  to  its  high  operating  temperatures,  the  appliance 
should  be located out of traffic & away from furniture and 
draperies.

  Children and adults should be alerted to the hazards 

of the high surface temperature, which could cause 
burns or clothing ignition.

  Young children should be carefully supervised when 

they are in the same room as the appliance.

  Clothing or other flammable materials should not be 

placed on or near the appliance.

Summary of Contents for H52-DFN





















Reviews: