background image

Page

XG0305

MD34-BV Homefire

For Your Safety - READ BEFORE LIGHTING:

To Turn Off Gas To Appliance:

Lighting  Instructions:

  If you cannot reach your gas supplier, call the Fire 

Department.

C.

  Use only your hand to push in or turn the gas control knob. 

Never use tools. If  the knob will not push in or turn by 
hand, don't try to repair it, call a qualified service technician. 
Force or attempt to repair may result in a fire or explosion.

D.

  Do not use this appliance if any part has been under water. 

Immediately call a qualified service technician to inspect 
the appliance and to replace any part of the control system, 
and any gas control which has been under water.

A. 

This appliance is equipped with an ignition system that 
lights the pilot burner automatically. 

Do not attempt to 

light the pilot by hand.

B.  BEFORE LIGHTING

 smell all around the appliance area for 

gas.  Be sure to smell next to the floor because some gas 
is heavier than air and will settle on the floor.

 

What To Do If You Smell Gas:

  Do not try to light any appliance.

  Do not touch any electrical switch; do not use any 

phone in your building.

  Immediately call your gas supplier from a neighbour's 

phone. Follow the gas supplier's instructions.

1. 

Turn off remote switch.

2. 

Flip down lower trim.

3. 

Turn the switch on the gas control to "Off".

4. 

Flip up trim.

1.

 

STOP!  

Read the safety information above on this label.

2.

  Flip down lower trims.

3.

  Turn switch on the gas control to OFF".

4.

  Wait 5 minutes to clear out any gas.  If you smell gas,

 

STOP! 

Follow "B" in the safety information above on this 

label.  If you don't smell gas, go to the next step.

5.

  Turn switch on the gas control to "ON".

 NOTE:

 This unit is 

equipped with an ignition system that lights the pilot burner 
automatically. 

Do not attempt to light the pilot by hand.

6.

  Turn on wall switch.

7.

  Flip up lower trim.

8.

  If the fireplace does not operate, follow the instructions "To 

Turn Off Gas To Appliance" and call your service technician 
or gas supplier.

with Electronic (Intermittent) Ignition

WARNING:

 

If you do not follow these instructions exactly, a fire or explosion 

may result causing property damage, personal injury or loss of life.

Operation -  Model MD34-BV-I 

Gas

Inlet

Gas Control Switch
Shown in "On" Position

Summary of Contents for MD34-BV Homefire Plus















Reviews: